Invacare 1106628 manual Installing the Seat Cushion Figure, Rear, Wheelchair Front

Page 40

BACK/SEAT

PROCEDURE 6

BACK/SEAT

 

 

INSTALLING THE SEAT CUSHION (FIGURE 8)

WARNING

The seat cushion IS NOT designed for use in the treatment of pressure sores or by individuals at risk of developing pressure sores.

Your therapist and physician should be consulted if you have any questions regarding weight relief, self-examination of the skin, or individual limitations and needs.

Make sure the hook and loop fastening strips are securely attached between the seat pan and cushion before using.

CAUTION

The cover is designed to protect the foam against a user’s incontinence and to provide fire retardency so the cushion must not be used without its cover. If the cover is torn, it must be replaced.

Machine wash cold. Gentle cycle. Mild detergent. NO fabric softeners or bleach. Tumble dry low or air dry. Warm or hot water or high dryer heat will reduce flame retardancy.

Wipe down surfaces with a slightly dampened cloth. DO NOT submerge cushion in water. If cushion foam becomes contaminated because of incontinence, it should be replaced beause the foam is absorbent and cannot be cleaned.

1.Perform one (1) of the following:

A.FLUSH MOUNT SEAT PAN - Position the cushion with the flap toward the REAR of the seat pan.

B.DROP MOUNT SEAT PAN - Position the cushion with the flap toward the FRONT of the seat pan.

2.Ensure the strips of loop fastener are on the underside of the cushion.

3.Align the front edge of the cushion with the front edge of the seat pan.

NOTE: Ensure the cushion is centered on the seat pan. Otherwise the hook and loop fastening strips will not engage properly.

WARNING

Make sure the hook and loop fastening straps are securely attached between the seat pan and cushion before using.

4.Secure the cushion to the seat pan, making sure that the strips of loop fastener on the cushion are securely attached to the strips of hook fastener on the seat pan.

Flap

Cushion

Strip of Loop Fastener

(Attached To Underside

of Cushion)

Strip of Hook Fastener

(Attached To Top of Seat Pan)

WHEELCHAIR Seat Pan

REAR

Front Of Cushion Lines Up With the Front Of the Seat Pan

NOTE: Flush mount seat pan shown.

WHEELCHAIR

FRONT

FIGURE 8 - INSTALLING THE SEAT CUSHION

Solara jr.™

40

Part No. 1106628

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Solara jr Solara jr Table of Contents Procedure 8 Wheel LOCKS/ANTI-TIPPERS Special Notes Special NotesLabel Locations Label LocationsSpecifications SpecificationsInvacare Solara JR Procedure General Guidelines Information for Healthcare PROFESSIONALS/ AssistantsGeneral Guidelines Anterior Forward TiltStability ALL Models Except Recliners Stability ALL ModelsStability Warning Operating Information Stability Recliner Models onlyGeneral Warnings Weight Training Weight LimitationStability and Balance SAFETY/HANDLING of WheelchairsCoping with Everyday Obstacles Percentage of Weight Distribution Unoccupied OccupiedMethod 1 Wheelchair with Step Tubes TippingStep Tube Stairways Tipping Curbs Method 2 Wheelchair Without Step TubeESCALATORS? Sorry Transferring to and from Other SeatsSafety Inspection Checklist Safety InspectionTroubleshooting MaintenanceProcedure 2SAFETY Inspection Maintenance Safety PrecautionsTransporting the Invacare Solara JR Transporting ProcedureTransporting INSTALLING/REMOVING Swingaway Footrest Figure Procedure Front RiggingsFront Friggings RemovingAdjusting Swingaway Footrest Height Front Riggings ProcedureHeight Adjustment Ranges Front RiggingsAdjusting Adjustable Angle FLIP-UP Footplates Figure Front Riggingsprocedure Composite Footplate DisassemblyReassembly Articulating Footplate Heel Loop ReplacementAdjusting the Elevating LEGREST/CALFPAD Assembly Figure Adjusting the LegrestAdjusting the Calfpad CalfpadUSING/ADJUSTING Dual Point Arms Figure ARMS/POSITIONING StrapsReplacing Dual Point ARM PAD Figure Procedure ARMS/POSITIONING StrapsReplacing Dual Point ARM Clothing Guards Figure Using Figure USING/INSTALLING/ADJUSTING Cantilever ArmsINSTALLING/ADJUSTING ARM PAD Replacement for Cantilever Arms Figure INSTALLING/REMOVING T-ARMS Figure Adjusting the T-ARMSInstalling T-ARMS Adjusting T-ARM Height FigureDepth Inside T-Arm Post Arm Release Lever Locked PositionOutside T- Arm Post SocketAdjusting T-ARM Transfer Assists AND/OR Side Guards Figure Adjusting T-ARM Sockets FigureHex screws and washers are removed Arm Arm Clamp Slot Arm SocketINSTALLING/REPLACING Seat Positioning Straps Figure ReplacingSide Guard Transfer Assist Socket ScrewsINSTALLING/REPLACING Chest Positioning Straps Figure Back Cane Locknut Hex Screw Chest Positioning StrapINSTALLING/REMOVING Stroller Handles Figure FOLDING/UNFOLDING Back Assembly FigureBACK/SEAT Installing Figure Detail a QUICK-RELEASE PIN InstalledRemoving Figure Quick-Release Pin Or bolt and locknut Recliners onlyLocked Position Procedure BACK/SEAT Adjusting FigureStroller Handle Thumbscrew Release Lever Using the Telescoping Back Canes Figure RAISING/LOWERINGStoring OpenINSTALLING/REPLACING the Back Upholstery Fixed Back Canes FigureREMOVING/INSTALLING the Spreader BAR Figure Installing and Removing a Seating SystemClamp Spreader Bar Set Screw Back Canes Rear Installing the Seat Cushion FigureWheelchair Front REMOVING/INSTALLING Rear Wheels Figure WHEELS/FORKS ProcedureWHEELS/FORKS Quick Release AxleAdjusting the Quick Release Axle Figure SEAT-TO-FLOOR Height AdjustmentProcedure WHEELS/FORKS Axle Mounting Plate Locking PinsAdjusting Forks Figure Fork Dust Cover Caster HeadtubeAdjusting Wheel Locks Figures 1 Procedure Wheel LOCKS/ANTI-TIPPERSWheel TIPPERS-LOCKS/ANTI 16-INCH Rear Wheels 18 24-INCH Rear WheelsFoot Activated Wheel Locks 12-INCH Wheels only Figure Using the Wheel LocksWheel LOCKS/ANTI-TIPPERS INSTALLING/ADJUSTING ANTI-TIPPERS Figure Adjusting2 to 2-inch ClearanceAnti-tipper Ground/FloorEngaging Tilt in SPACE/RECLINER Operation TILT/RECLINE ProcedureTILT/RECLINE Procedure TILT/RECLINE Engaging TILT-IN-SPACE FigureTILT-IN-SPACE Tilt SlideTILT/RECLINE Procedure Recliner Operation Figure Gas CylinderAdjusting Tilt Trigger Release Cables Figure Cable Locking Nut Trigger Release Lever Cable Adjusting NutAdjusting Upper Tilt Locking Collar Figure Bearing HousingPositioning Tilt Locking Collars Magnetic protractor reads desired angle of tiltReplacing the Back Upholstery Replacing the Headrest UpholsteryHeadrest Upholstery Extension Back Cane Back UpholsteryAdjusting the Back Height Recliner Models only Figure Inch Seat Cushion PositionContracture Assembly Angle Adjustment Figure Procedure Contracture FootplateFootplatecontracture Mounting ScrewUsing the Optional Quick Release PIN Figure Angle Adjustment of the Contracture Footplate FigureContracture Footplate Depth Adjustment Figure ContractureContracture Footplate Height Adjustment Figure Replacing the Contracture Footplate Heel Loop FigureMounting Hole ContractureSolara jr Solara jr Warranty Limited WarrantyWarranty One Invacare Way

1106628 specifications

The Invacare 1106628 is a robust and innovative mobility solution designed to enhance the quality of life for individuals with limited mobility. This power wheelchair combines advanced technology and user-friendly features, making it an excellent choice for both indoor and outdoor use.

One of the standout characteristics of the Invacare 1106628 is its versatile seating system, which provides optimal comfort and support. The seat is designed to accommodate various body types and can be adjusted to ensure perfect alignment and positioning. Additionally, the chair includes a contoured backrest that offers lumbar support, promoting good posture during extended use.

Technology plays a significant role in the design of the Invacare 1106628. The wheelchair is equipped with a powerful motor and a durable battery system, allowing for a long driving range and reliable performance. With a top speed that makes navigating urban settings easy, users can enjoy both independence and accessibility. The advanced joystick control allows for smooth and precise maneuvering, enabling efficient navigation through tight spaces.

The wheelchair also boasts a sturdy construction, ensuring it can withstand the rigors of daily use. The frame is made from high-quality materials, providing durability while remaining lightweight enough for easy transport. Its compact design enhances maneuverability, making it suitable for use in various environments, from bustling shopping malls to narrow hallways in homes.

Safety features are paramount in the design of the Invacare 1106628. The wheelchair comes with anti-tip wheels, ensuring stability during movement, particularly when climbing slopes or navigating uneven terrain. The durable tires are designed for excellent traction, further enhancing safety and control in various outdoor settings.

In terms of additional features, the Invacare 1106628 includes customizable options such as adjustable armrests, footrests, and various accessory attachments. This flexibility allows users to tailor the wheelchair to their specific needs, enhancing overall comfort and usability.

In conclusion, the Invacare 1106628 is a well-engineered power wheelchair that incorporates advanced technology, safety features, and customizable options. It is designed to provide individuals with mobility challenges the independence and support they need, making it a valuable asset for users seeking to improve their quality of life. Whether navigating through their home or enjoying the great outdoors, the Invacare 1106628 delivers on performance, comfort, and durability.
Top Page Image Contents