Invacare 1106628 manual INSTALLING/REMOVING T-ARMS Figure, Adjusting the T-ARMS, Installing T-ARMS

Page 29

ARMS/POSITIONING STRAPS

PROCEDURE 5

 

 

INSTALLING/REMOVING T-ARMS (FIGURE 5)

INSTALLING T-ARMS

1.Position the T-arm over the T-arm socket on the wheelchair frame.

NOTE: Make sure the locking lever is towards the front of the wheelchair.

2.Slide T-arm into T-arm socket until the locking lever is in the slot in the T-arm socket and an audible "click" is heard.

3.Pull up on T-arm to make sure T-arm is locked in place.

NOTE: If the T-arm does not slide in the T-arm socket as desired, adjust the T-arm socket. Refer to ADJUST- ING THE T-ARMS in this procedure of the manual.

4.Adjust the T-arm for desired height, width and depth, if necessary. Refer to ADJUSTING THE T-ARMS in this procedure of the manual.

5.Repeat STEPS 1-4 for opposite side of wheelchair.

REMOVING T-ARMS

T-Arm

Wheelchair

 

Frame

Locking Lever

 

(towards the front

T-Arm

of the wheelchair)

Socket

 

 

Slot

FIGURE 5 - INSTALLING/

REMOVING T- ARMS

ARMS/POSITIONING STRAPS

1. Press in on the locking lever and lift the T-arm straight up and out of the T-arm socket.

NOTE: If the T-arm does not slide up and down in the T-arm socket as desired, adjust the T-arm socket. Refer to ADJUSTING THE T-ARMS in this procedure of the manual.

2. Repeat STEP 2 for opposite side of the wheelchair.

ADJUSTING THE T-ARMS

ADJUSTING T-ARM HEIGHT (FIGURE 6)

1. Unlock the T-arm by flipping the T-arm release lever towards the inside of the wheelchair.

NOTE: If necessary, pull out on the T-arm release lever and rotate 180° so it can be flipped towards the outside of the wheelchair.

2.Slide the T-arm to one (1) of:

A.Low Height T-Arms- Nine (9) positions.

B.High Height T-Arms- Seven (7) positions.

NOTE: If the inside T-arm post does not slide up and down in the outside T-arm post as desired, perform one (1) of the following:

A.Tighten - Tightening the set screws on the outside T-arm post will make it more difficult to move the inside T-arm post up and down.

B.Loosen - Loosening the set screws on the outside T-arm post will make it easier to move the inside T-arm post up and down.

3.Lock the T-arm by flipping the T-arm release lever towards the front of the wheelchair.

Part No. 1106628

29

Solara jr.™

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Solara jr Solara jr Table of Contents Procedure 8 Wheel LOCKS/ANTI-TIPPERS Special Notes Special NotesLabel Locations Label LocationsInvacare Solara JR SpecificationsSpecifications Information for Healthcare PROFESSIONALS/ Assistants Procedure General GuidelinesGeneral Guidelines Anterior Forward TiltStability Warning Stability ALL ModelsStability ALL Models Except Recliners General Warnings Stability Recliner Models onlyOperating Information Weight Limitation Weight TrainingCoping with Everyday Obstacles SAFETY/HANDLING of WheelchairsStability and Balance Unoccupied Occupied Percentage of Weight DistributionStep Tube TippingMethod 1 Wheelchair with Step Tubes Tipping Curbs Method 2 Wheelchair Without Step Tube StairwaysTransferring to and from Other Seats ESCALATORS? SorrySafety Inspection Safety Inspection ChecklistMaintenance TroubleshootingProcedure 2SAFETY Inspection Maintenance Safety PrecautionsTransporting Transporting ProcedureTransporting the Invacare Solara JR Procedure Front Riggings INSTALLING/REMOVING Swingaway Footrest FigureFront Friggings RemovingFront Riggings Procedure Adjusting Swingaway Footrest HeightHeight Adjustment Ranges Front RiggingsAdjusting Adjustable Angle FLIP-UP Footplates Figure Composite Footplate Disassembly Front RiggingsprocedureReassembly Articulating Footplate Heel Loop ReplacementAdjusting the Legrest Adjusting the Elevating LEGREST/CALFPAD Assembly FigureAdjusting the Calfpad CalfpadARMS/POSITIONING Straps USING/ADJUSTING Dual Point Arms FigureReplacing Dual Point ARM Clothing Guards Figure Procedure ARMS/POSITIONING StrapsReplacing Dual Point ARM PAD Figure INSTALLING/ADJUSTING USING/INSTALLING/ADJUSTING Cantilever ArmsUsing Figure ARM PAD Replacement for Cantilever Arms Figure Adjusting the T-ARMS INSTALLING/REMOVING T-ARMS FigureInstalling T-ARMS Adjusting T-ARM Height FigureInside T-Arm Post Arm Release Lever Locked Position DepthOutside T- Arm Post SocketAdjusting T-ARM Sockets Figure Adjusting T-ARM Transfer Assists AND/OR Side Guards FigureHex screws and washers are removed Arm Arm Clamp Slot Arm SocketReplacing INSTALLING/REPLACING Seat Positioning Straps FigureSide Guard Transfer Assist Socket ScrewsBack Cane Locknut Hex Screw Chest Positioning Strap INSTALLING/REPLACING Chest Positioning Straps FigureBACK/SEAT FOLDING/UNFOLDING Back Assembly FigureINSTALLING/REMOVING Stroller Handles Figure Detail a QUICK-RELEASE PIN Installed Installing FigureRemoving Figure Quick-Release Pin Or bolt and locknut Recliners onlyStroller Handle Thumbscrew Release Lever Procedure BACK/SEAT Adjusting FigureLocked Position RAISING/LOWERING Using the Telescoping Back Canes FigureStoring OpenFixed Back Canes Figure INSTALLING/REPLACING the Back UpholsteryClamp Spreader Bar Set Screw Back Canes Installing and Removing a Seating SystemREMOVING/INSTALLING the Spreader BAR Figure Wheelchair Front Installing the Seat Cushion FigureRear WHEELS/FORKS Procedure REMOVING/INSTALLING Rear Wheels FigureWHEELS/FORKS Quick Release AxleSEAT-TO-FLOOR Height Adjustment Adjusting the Quick Release Axle FigureProcedure WHEELS/FORKS Axle Mounting Plate Locking PinsFork Dust Cover Caster Headtube Adjusting Forks FigureProcedure Wheel LOCKS/ANTI-TIPPERS Adjusting Wheel Locks Figures 1Wheel TIPPERS-LOCKS/ANTI 16-INCH Rear Wheels 18 24-INCH Rear WheelsWheel LOCKS/ANTI-TIPPERS Using the Wheel LocksFoot Activated Wheel Locks 12-INCH Wheels only Figure Adjusting INSTALLING/ADJUSTING ANTI-TIPPERS Figure2 to 2-inch ClearanceAnti-tipper Ground/FloorTILT/RECLINE TILT/RECLINE ProcedureEngaging Tilt in SPACE/RECLINER Operation Engaging TILT-IN-SPACE Figure Procedure TILT/RECLINETILT-IN-SPACE Tilt SlideGas Cylinder TILT/RECLINE Procedure Recliner Operation FigureCable Locking Nut Trigger Release Lever Cable Adjusting Nut Adjusting Tilt Trigger Release Cables FigureBearing Housing Adjusting Upper Tilt Locking Collar FigurePositioning Tilt Locking Collars Magnetic protractor reads desired angle of tiltReplacing the Headrest Upholstery Replacing the Back UpholsteryHeadrest Upholstery Extension Back Cane Back UpholsteryInch Seat Cushion Position Adjusting the Back Height Recliner Models only FigureProcedure Contracture Footplate Contracture Assembly Angle Adjustment FigureFootplatecontracture Mounting ScrewAngle Adjustment of the Contracture Footplate Figure Using the Optional Quick Release PIN FigureContracture Footplate Depth Adjustment Figure ContractureReplacing the Contracture Footplate Heel Loop Figure Contracture Footplate Height Adjustment FigureMounting Hole ContractureSolara jr Solara jr Warranty Limited WarrantyWarranty One Invacare Way

1106628 specifications

The Invacare 1106628 is a robust and innovative mobility solution designed to enhance the quality of life for individuals with limited mobility. This power wheelchair combines advanced technology and user-friendly features, making it an excellent choice for both indoor and outdoor use.

One of the standout characteristics of the Invacare 1106628 is its versatile seating system, which provides optimal comfort and support. The seat is designed to accommodate various body types and can be adjusted to ensure perfect alignment and positioning. Additionally, the chair includes a contoured backrest that offers lumbar support, promoting good posture during extended use.

Technology plays a significant role in the design of the Invacare 1106628. The wheelchair is equipped with a powerful motor and a durable battery system, allowing for a long driving range and reliable performance. With a top speed that makes navigating urban settings easy, users can enjoy both independence and accessibility. The advanced joystick control allows for smooth and precise maneuvering, enabling efficient navigation through tight spaces.

The wheelchair also boasts a sturdy construction, ensuring it can withstand the rigors of daily use. The frame is made from high-quality materials, providing durability while remaining lightweight enough for easy transport. Its compact design enhances maneuverability, making it suitable for use in various environments, from bustling shopping malls to narrow hallways in homes.

Safety features are paramount in the design of the Invacare 1106628. The wheelchair comes with anti-tip wheels, ensuring stability during movement, particularly when climbing slopes or navigating uneven terrain. The durable tires are designed for excellent traction, further enhancing safety and control in various outdoor settings.

In terms of additional features, the Invacare 1106628 includes customizable options such as adjustable armrests, footrests, and various accessory attachments. This flexibility allows users to tailor the wheelchair to their specific needs, enhancing overall comfort and usability.

In conclusion, the Invacare 1106628 is a well-engineered power wheelchair that incorporates advanced technology, safety features, and customizable options. It is designed to provide individuals with mobility challenges the independence and support they need, making it a valuable asset for users seeking to improve their quality of life. Whether navigating through their home or enjoying the great outdoors, the Invacare 1106628 delivers on performance, comfort, and durability.
Top Page Image Contents