ClearOne comm 600, 900 To select a frequency, To perform RF radio test, To enter flash duration

Page 32

58

Using the RAV — Programming Phone Preferences

Using the RAV— Programming Phone Preferences

 

59

 

To select a frequency

1.Press to access the menu options.

2.Scroll to Configuration and press .

3.Scroll to Frequency and press .

4.Choose a frequency from 1–8.

5.Press to save the frequency and return to the Configuration menu.

Note: The channel frequency allows the mixer to communicate with the controller. The frequency in RAV-Ware must match the RAV controller frequency. See page 32.

Frequency 1

Frequency 2 *

Frequency 3

Figure 4.16. Select a frequency

Note: If you are using the European or South African version of RAV frequency 1 and frequency 8 are the same frequency.

To perform RF radio test

1.Press to access the menu options.

2.Scroll to Configuration and press .

3.Scroll to RF Radio Test and press .

4.Press to exit and return to the Configuration menu.

Note: The RF Controller will send out a radio signal and display the signal strength between the Controller and the mixer. Use this feature to ensure the mixer and Controller are set to the same frequency and to verify of the signal strength. Use

RF Radio Test

-------

Exit

Figure 4.18. RF Radio test

Signal Level

Reliability

0–4 bars

Fair

 

 

4–8 bars

Good

To enter flash duration

1.

Press

to access the menu options.

 

2.

Scroll to Configuration and press

.

3.

Scroll to Flash Duration and press

.

1000 Save

the chart to determine the reliability of the signal.

!Attention: If you are having trouble with the communication between the Controller and the mixer, refer to the Troubleshooting guide for tips on improving signal strength.

9–12 bars

Better

 

 

13–16 bars

Best

Figure 4.19. Signal strength reliability

4.

Type the duration number from

 

50–1000 ms.

5.

Press

to save the duration and return

 

to the Configuration menu.

Figure 4.17. Enter flash settings

To change LCD contrast

1.Press to access the menu options.

2.Scroll to Configuration and press .

3.Scroll to Contract and press .

4.Choose a contrast setting (0–3).

5.Press to select the contrast and return to the Configuration menu.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Contrast 0

*

 

 

 

 

 

Contrast 1

 

 

 

 

 

Contrast 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 4.20. Contrast

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Page Table of Contents Introduction Services and support RAV 600/900Product returns UnpackingMixer Product OverviewRF Radio Frequency Controller Microphone Pods Basic Room DesignBasic Room Design for RAV Speakers ceiling- or wall-mountInstallation Overview System Requirements for RAV-Ware Network InformationConnecting the RAV Audio conferencing To set up audio conferencingBasic Connections Attach the external antenna and turn it it is upright Connecting video codecs, amplifiers and sound cards Auxiliary DevicesTo connect to a video codec To connect to a sound cardConnecting VCRs and DVD players Connecting PTZ camerasConnecting for serial control Connecting for USB controlDigital phones To connect to a digital phoneRAV-Ware Software Configuration Install RAV-Ware IntroductionGetting started with RAV-Ware RAV-Ware overviewRAV-Ware connections RAV-Ware filesNetwork Find Configuring System SettingsCommunication Settings Regional Settings Telephone SettingsCustomizing RAV Components MicrophonesMixer Console Effects of using an external amplifierLoudspeakers Line Input and Output Preconfigured video codecs, amplifiers and sound cardsAdjusting Line Input/Output settings Record and Playback Preconfigured record/playback devicesAdjusting Record/Playback settings Setting camera presets Camera ControlsDialer and Phonebook Usage PhonebookDialer Event Log Advanced FeaturesSystem Checks Device Toolbox Editor Error MessagesFirmware upgrades Using the RAV Using the Controller Managing CallsProgramming Phone Preferences Using the Phonebook from the RF ControllerAccessing the menu Adjusting the Settings ConfigurationTo select a frequency To perform RF radio testTo enter flash duration To change LCD contrastTo view the IP address To check the RAV versionWeb Interface Dial Accessing the web interfaceOverview To download log To open event logTo clear log To open the system checks System CheckLog Out Appendix Maintenance TroubleshootingAudio ControllerSpeakers PinoutsCamera pinouts GeneralSpecifications DimensionsSerial Commands Command structureConventions Groups and channelsMeter type definitions Serial command error codesRAV serial commands AA Auto Answer Enable/ Disable Aarings Number of Rings to Auto Answer OnAD Auto Disconnect Enable/ Disable AEC Acoustic Echo Canceller enable/ disableAecref Acoustic Echo Cancellation Reference Aconn Audible Connect / Disconnect IndicationBatterylvl Battery Level Camctrlmode Camera Control Port ModeBaud Baud Rate Calldur Call DurationCampreset Camera Preset Campresetset Camera Preset SetupCamflow Camera Control Flow Control Cammove Move the CameraCAMPRESETSET2 Camera Preset Setup Camswitchlag Camera Switch Time LagCamposition Camera Position Camtrack Camera TrackDefault Default The Unit Cleareffect Clear Effect Wide Band Telco EmulationClock Clock Set Country Country SelectionDid Device ID Device Device Identification LabelDial Dtmf Dialing Enetgate Ethernet default Gateway address Enetaddr Ethernet port IP addressEnetdhcp Ethernet Dhcp Selection Enetdnsa Ethernet DNS Server addressesEqsel Equalization Enable Gain Gain AdjustmentEQ Equalization Flow Flow ControlGreport Gate Report Hook Hook FlashHookd Hook Flash Duration Label LabelLvlreporten Level Report Enable LVL LevelLvlreport Level Report Manufacturer Manufacturer Identification LabelMiccampreset Mic Camera Preset Ncsel Noise Cancellation SelectMtrx Matrix Routing Mute MutePbdial Dial a PB Entry by Name Phonebookadd Adds an Entry to the PhonebookPhonebookcnt Queries the Number of Entries in the Phonebook Phonebookdel Deletes an Entry to the PhonebookReset Reset Redial Dial the last number againRffreq RF Frequency Selection Ring Ring IndicationSilenceprst Silence Camera Preset Ringerlvl Audible Ring LevelRingersel Audible Ring Melody Selection Ringertest Audible Ring Melody TestStereomix Sets the Input to be a Stereo Mix Syschecks System ChecksSysresult System Check Result 112TE Telco Enable Telcolvlctrl Telco TX Level Control Enable/ DisableVolume Volume Adjustment UID Unit IDElectrical Safety Advisory ComplianceFCC Part 15/ICES-003 Compliance FCC Part 68 ComplianceEuropean Compliance EC Declaration of ConformityIndex
Related manuals
Manual 63 pages 19.21 Kb

600, 900 specifications

ClearOne Comm 900,600 is a cutting-edge communication platform designed to enhance audio and video conferencing experiences in both corporate and educational environments. With its advanced technology and user-friendly interface, ClearOne Comm 900,600 addresses the increasing demand for seamless collaboration in a hybrid work scenario.

One of the standout features of the ClearOne Comm 900,600 is its exceptional audio quality. Utilizing advanced beamforming microphone technology, the system captures sound from multiple directions while minimizing background noise. This ensures that every participant in a conference call is heard clearly, regardless of their position in the room. The system also supports high-definition audio processing, delivering crystal-clear sound that enhances the overall communication experience.

The ClearOne Comm 900,600 is equipped with state-of-the-art video capabilities as well, making it suitable for various applications. It supports high-definition video resolutions, enabling users to engage with their audience visually without compromising quality. The system is compatible with various video conferencing applications, ensuring flexibility for users who may prefer specific software solutions.

Another significant characteristic of the ClearOne Comm 900,600 is its scalability. Organizations can easily expand the system according to their needs. Whether it's a small meeting room or a large auditorium, the Comm 900,600 can be configured to accommodate various room sizes and setups. It provides multiple connection options, including USB and HDMI, making it easy to integrate with existing equipment.

Additionally, the ClearOne Comm 900,600 boasts a user-friendly interface that simplifies operation for all participants. Its intuitive controls ensure that even those unfamiliar with technology can navigate the system effortlessly. This focus on usability promotes a smooth and efficient meeting environment, which is essential in today’s fast-paced work culture.

Lastly, the ClearOne Comm 900,600 features robust security measures to protect sensitive data. It employs encryption protocols to safeguard communications while also adhering to industry standards for data protection. This ensures that organizations can conduct confidential discussions without concern for unauthorized access.

In conclusion, the ClearOne Comm 900,600 is an innovative solution for modern communication needs, offering advanced audio and video technologies, scalability, user-friendly operation, and strong security features. It is an essential tool for promoting effective collaboration in any organization.
Top Page Image Contents