ClearOne comm 900, 600 Serial command error codes, RAV serial commands, Meter type definitions

80 Appendix— Serial Commands

Meter type definitions

Alpha	Numeric	Level position	Level position	Level position	Level position	Level position
		for Mic Pods	for Line Inputs	for Outputs	for Telco Transmits	for Telco Receives
A	2	Maximum level	Level after PEQ	Level after PEQ	Level after gain	Level after gain
		of the three	and gain	and gain		adjustment
		microphones on the
		pod after processing
R	5	Echo Return Loss	N/A	N/A	N/A	N/A
E	6	Echo Return Loss	N/A	N/A	N/A	N/A
T	7	ERL + ERLE	N/A	N/A	N/A	N/A

Serial command error codes

Error number	Text message	Explanation/Solution
1	Memory error	The box is out of internal memory.
		Power cycle the box.
2	No command found	A command was not found in the string.
3	Unknown command	A command was executed on a different
		device type that this box response can
		not display. The command dictionary
		needs to be updated.
4	Not implemented	The command is not implemented.
5	Argument error	The command had an argument that was
		out of range.
6	Unknown command	The command is unknown to this unit.
7	Bad checksum	The binary command’s checksum is
		wrong.
8	Camera not responding	A preset or macro failed to program
		because it is too large or because its
		command list contained an invalid
		command.
11	Command too big	The binary command is too large.

Appendix— Serial Commands 81

RAV serial commands

Command	Function
AA	Selects/reports setting of auto answer
AARINGS	Selects/reports setting of the number of rings to auto answer
ACONN	Selects/reports status of audible connect/disconnect indication
AD	Selects/reports setting of auto disconnect
AEC	Selects/reports acoustic echo canceller setting
AECREF	Enables/disables or reports current status of AEC reference
AGC	Selects/reports AGC
BATTERYLVL	Reports battery level on remote
BAUD	Selects/reports the baud rate of the serial port
CALLDUR	Indicates how long a call has lasted
CAMBAUD	Selects/reports baud rate of camera control port
CAMCTRLMODE	Sets/reports camera control port mode
CAMFLOW	Selects/reports flow control of camera control port
CAMMOVE	Sends command to move the camera on the camera control port
CAMPRESET	Executes camera preset
CAMPRESETSET	Sets current position of camera as preset
CAMPRESETSET2	Sets/reports current camera preset
CAMPOSITION	Sets/reports current position of camera on the camera control port
CAMSWITCHLAG	Set the switch time lag for voice tracking
CAMTRACK	Selects/reports camera voice-tracking mode
CAMZOOM	Sets/reports current zoom of camera on the camera control port
CLEAREFFECT	Enables/disables or reports current status of clear effect
CLOCK	Sets/reports current time
COUNTRY	Sets/reports country for compliance
DEFAULT	Sets the unit to default
DEVICE	Selects/reports manufacturer identification label
DEVICETYPE	Enables /disables or reports the current type of device connected to
	an input or output
DIAL	Dials DTMF sequence or reports last sequence dialed
DID	Selects/reports device ID
ENETADDR	Selects/reports IP address of the Ethernet port
ENETDHCP	Selects/reports use of DHCP of the Ethernet port
ENETDNSA	Selects/reports DNS server IP address of the Ethernet port
ENETDNX	Selects/reports use of the DNS of the Ethernet port
ENETGATE	Selects/reports default gateway of the Ethernet port
ENETSUBN	Selects/reports subnet mask of the Ethernet port
EQ	Enables/disables or reports current status of equalization
EQSEL	Enables/disables or reports current status of equalization
FLOW	Selects/reports the flow control of the serial port
GAIN	Changes/reports gain for a channel
GATE	Reports gate status of microphones
GREPORT	Selects/reports gate status report frequency
HOOK	Sends a hook flash
HOOKD	Selects/reports hook flash duration

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760 Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760