ClearOne comm 900, 600 user manual Overview, Accessing the web interface, Dial

Page 35

 

64

 

Web Interface — Overview

Overview

Accessing the web interface

The RAV has a built-in web server that provides a remote access interface to your RAV system. However, not all programming and metering functions are available.The web interface allows you to connect to a RAV unit, run system checks, view the event log and manage calls.

To use the web interface from outside your network, your firewall must be properly configured to allow access. If you are accessing RAV from within the network, you may use the network name. The web interface uses Port 80.

To connect to RAV through the web interface

1.Open a web browser and enter the IP address or Network Name of the RAV in the address bar.

2.Enter your User Name and Password.The default user name is ClearOne and the default password is RAV.

Web Interface — Overview

 

65

 

Dial

You can make all your calls from the Dialer in the web interface. You can dial a number, redial the last dialed call and disconnect calls. You can also use flash settings, mute the microphones and adjust volume.

To open the dialer window

•Click the Dial button in the left channel navigation.

The RAV web interface opens. Navigation buttons are shown in the left channel.

Figure 5.1. Network Password

Figure 5.3. Dialer window

To make a call

1.Click the ON/OFF button to take the phone off-hook.

2.Using the number pad, dial a phone number just as you would on a standard phone.

Note: You can also pre-dial the number and press the ON/OFF button to connect the call.

Tip: You can also dial using the 0-9, star (*) and number (#) on your on your keyboard. Use the comma (,) key to enter a two second pause.The Enter key connects to and disconnects from the telephone line.

Figure 5.2. RAV-Ware management system

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Page Table of Contents Introduction Unpacking Services and supportRAV 600/900 Product returnsMixer Product OverviewRF Radio Frequency Controller Speakers ceiling- or wall-mount Microphone PodsBasic Room Design Basic Room Design for RAVInstallation Overview Network Information System Requirements for RAV-WareConnecting the RAV Audio conferencing To set up audio conferencingBasic Connections Attach the external antenna and turn it it is upright To connect to a sound card Connecting video codecs, amplifiers and sound cardsAuxiliary Devices To connect to a video codecConnecting for USB control Connecting VCRs and DVD playersConnecting PTZ cameras Connecting for serial controlTo connect to a digital phone Digital phonesRAV-Ware Software Configuration RAV-Ware overview Install RAV-WareIntroduction Getting started with RAV-WareRAV-Ware files RAV-Ware connectionsNetwork Find Configuring System SettingsCommunication Settings Telephone Settings Regional SettingsMicrophones Customizing RAV ComponentsMixer Console Effects of using an external amplifierLoudspeakers Line Input and Output Preconfigured video codecs, amplifiers and sound cardsAdjusting Line Input/Output settings Record and Playback Preconfigured record/playback devicesAdjusting Record/Playback settings Phonebook Setting camera presetsCamera Controls Dialer and Phonebook UsageDialer Event Log Advanced FeaturesSystem Checks Device Toolbox Editor Error MessagesFirmware upgrades Using the RAV Managing Calls Using the ControllerProgramming Phone Preferences Using the Phonebook from the RF ControllerAccessing the menu Configuration Adjusting the SettingsTo change LCD contrast To select a frequencyTo perform RF radio test To enter flash durationTo check the RAV version To view the IP addressWeb Interface Dial Accessing the web interfaceOverview To download log To open event logTo clear log To open the system checks System CheckLog Out Appendix Controller MaintenanceTroubleshooting AudioGeneral SpeakersPinouts Camera pinoutsDimensions SpecificationsGroups and channels Serial CommandsCommand structure ConventionsMeter type definitions Serial command error codesRAV serial commands Aarings Number of Rings to Auto Answer On AA Auto Answer Enable/ DisableAconn Audible Connect / Disconnect Indication AD Auto Disconnect Enable/ DisableAEC Acoustic Echo Canceller enable/ disable Aecref Acoustic Echo Cancellation ReferenceCalldur Call Duration Batterylvl Battery LevelCamctrlmode Camera Control Port Mode Baud Baud RateCammove Move the Camera Campreset Camera PresetCampresetset Camera Preset Setup Camflow Camera Control Flow ControlCamtrack Camera Track CAMPRESETSET2 Camera Preset SetupCamswitchlag Camera Switch Time Lag Camposition Camera PositionCountry Country Selection Default Default The UnitCleareffect Clear Effect Wide Band Telco Emulation Clock Clock SetDid Device ID Device Device Identification LabelDial Dtmf Dialing Enetdnsa Ethernet DNS Server addresses Enetgate Ethernet default Gateway addressEnetaddr Ethernet port IP address Enetdhcp Ethernet Dhcp SelectionFlow Flow Control Eqsel Equalization EnableGain Gain Adjustment EQ EqualizationLabel Label Greport Gate ReportHook Hook Flash Hookd Hook Flash DurationManufacturer Manufacturer Identification Label Lvlreporten Level Report EnableLVL Level Lvlreport Level ReportMute Mute Miccampreset Mic Camera PresetNcsel Noise Cancellation Select Mtrx Matrix RoutingPhonebookdel Deletes an Entry to the Phonebook Pbdial Dial a PB Entry by NamePhonebookadd Adds an Entry to the Phonebook Phonebookcnt Queries the Number of Entries in the PhonebookRing Ring Indication Reset ResetRedial Dial the last number again Rffreq RF Frequency SelectionRingertest Audible Ring Melody Test Silenceprst Silence Camera PresetRingerlvl Audible Ring Level Ringersel Audible Ring Melody Selection112 Stereomix Sets the Input to be a Stereo MixSyschecks System Checks Sysresult System Check ResultUID Unit ID TE Telco EnableTelcolvlctrl Telco TX Level Control Enable/ Disable Volume Volume AdjustmentFCC Part 68 Compliance Electrical Safety AdvisoryCompliance FCC Part 15/ICES-003 ComplianceEC Declaration of Conformity European ComplianceIndex
Related manuals
Manual 63 pages 19.21 Kb

600, 900 specifications

ClearOne Comm 900,600 is a cutting-edge communication platform designed to enhance audio and video conferencing experiences in both corporate and educational environments. With its advanced technology and user-friendly interface, ClearOne Comm 900,600 addresses the increasing demand for seamless collaboration in a hybrid work scenario.

One of the standout features of the ClearOne Comm 900,600 is its exceptional audio quality. Utilizing advanced beamforming microphone technology, the system captures sound from multiple directions while minimizing background noise. This ensures that every participant in a conference call is heard clearly, regardless of their position in the room. The system also supports high-definition audio processing, delivering crystal-clear sound that enhances the overall communication experience.

The ClearOne Comm 900,600 is equipped with state-of-the-art video capabilities as well, making it suitable for various applications. It supports high-definition video resolutions, enabling users to engage with their audience visually without compromising quality. The system is compatible with various video conferencing applications, ensuring flexibility for users who may prefer specific software solutions.

Another significant characteristic of the ClearOne Comm 900,600 is its scalability. Organizations can easily expand the system according to their needs. Whether it's a small meeting room or a large auditorium, the Comm 900,600 can be configured to accommodate various room sizes and setups. It provides multiple connection options, including USB and HDMI, making it easy to integrate with existing equipment.

Additionally, the ClearOne Comm 900,600 boasts a user-friendly interface that simplifies operation for all participants. Its intuitive controls ensure that even those unfamiliar with technology can navigate the system effortlessly. This focus on usability promotes a smooth and efficient meeting environment, which is essential in today’s fast-paced work culture.

Lastly, the ClearOne Comm 900,600 features robust security measures to protect sensitive data. It employs encryption protocols to safeguard communications while also adhering to industry standards for data protection. This ensures that organizations can conduct confidential discussions without concern for unauthorized access.

In conclusion, the ClearOne Comm 900,600 is an innovative solution for modern communication needs, offering advanced audio and video technologies, scalability, user-friendly operation, and strong security features. It is an essential tool for promoting effective collaboration in any organization.
Top Page Image Contents