GE 28225 manual Intercom Operation, Paging the Handset, Key Lock, Making Intercom Calls

Page 29

Paging the Handset

If a handset has been misplaced, it is possible to call all the handsets. The handset will ring at full volume regardless of any programmed pre-set.

1.Press the page button briefly on the base station.

To stop the page call:

1. Quickly press and release the /flash, /end, or
button on the handset or page button on the base.
Key Lock
Press the and hold the	button for 2 seconds to activate or
de-activate the key lock.

When handset keys are locked, you are still able to receive incoming calls by pressing the /flash button.

Intercom Operation

Making Intercom Calls

If more than one handset is registered on the base station, it is possible to make intercom calls between the handsets.

1. Press the INT (SKR) button.

2. Use the or button to select the required handset (Handset 1 or Handset 2).

3.Press the OK (SKL) button to initiate the conversation.

4.Press the/end button to end the call.

NOTE: During the conversation, you can use

or button to adjust the speaking volume (5 levels).

Receiving Intercom Calls

When an intercom call arrives, the handset rings and displays the caller’s handset number. flashes in the handset display.

1.Press the /flash button to establish the connection.

NOTE: If auto answer is enabled, the line can also be automatically connected after the handset is lifted up from the base.

2.Press the/end button to terminate the call.

29

Image 29

Contents DECT6.0 Interference Information Important InformationREN Number Telephone Network InformationHearing Aid Compatibility HAC LicensingInformation for Dect Product FCC RF Radiation Exposure StatementTable of Contents General Product Care Introduction Parts Checklist for 28225xx2 ModelBefore You Begin Telephone Jack RequirementsDigital Security System InstallationAvoid areas of excessive dust, moisture and low temperature Important Installation GuidelinesBase Layout Display Icons Handset LayoutInstalling the Handset Batteries Installing the PhoneBase Station Setting the Voice Language Answering System SetupAnswering System ON/OFF Recording the Outgoing AnnouncementAnnounce Only On/Off Remote Access CodeMessage Alert Sample Outgoing AnnouncementCall Screening Rings to AnswerProgramming Your Phone Handset SettingsMain Menu Date & TimeRinger Volume Ringer SetupGroup Melody RingtoneRegistration Set AlarmAuto Talk Deregister Handset Select BaseTones ON/OFF Reset Handset Handset Display SettingsWallpaper Handset NameDial Mode Base SetupHandset Language Area CodePress the Soft Key Left SKL button Answering System Setup via the HandsetListening to Your Messages Answering System OperationMessage Playback Deleting MessagesMemo Recording Base Ringer VolumeTo delete all old messages with the handset To record a Memo at the BaseRemote Operation Memory FullImportant Information Receiving a Call Handset OperationMaking a Call Redialing Changing the Earpiece VolumeHandset Speaker Phone Muting the MicrophonePaging the Handset Intercom OperationKey Lock Making Intercom CallsAfter receiving an external call Three Party ConferenceCall Transfer / Forwarding Receiving CID Records Caller ID CIDCall Waiting Caller ID Dialing a CID Number Reviewing CID Records In CID MemoryAs you cannot reformat CID records stored in memory Storing CID Records in Internal MemoryDeleting a CID Record New Entry Programming the Phone BookDeleting All CID Records Delete Entry Edit EntryDialing from the Phone Book Call List Delete AllIf you choose Delete Entry If you choose Save NumberChanging the Batteries Battery Safety PrecautionsIf you choose Delete All If you choose User NumberAnswering System Display Messages Display MessagesTroubleshooting Guide Handset Sound SignalsCordless Phone Solutions Telephone SolutionsMove closer to base. The handset might be out of range Battery SolutionsGeneral Product Care Answering System SolutionsCauses of Poor Reception Accessory InformationWarranty 14 F IndexMemory Model