GE 28225 manual Handset Sound Signals, Troubleshooting Guide, Cordless Phone Solutions

Page 39

Handset Sound Signals

Signal	Meaning
A long warbling tone	Signals an incoming call
(with ringer on)
Three short beeps	Page signal
(several times)
Single beep every 7 seconds	Low battery warning

Troubleshooting Guide

Cordless Phone Solutions

No Display

•The battery must be fully charged. Try replacing the battery.

Registration will not work

•The battery must be fully charged. Charge the battery for 16 hours.

•Make sure that the unit is connected to a non-switched electrical outlet. Disconnect the unit from the wall and plug it in again.

•You must be subscribed to Caller ID service from your local telephone company in order to receive Caller ID records.

Telephone Solutions

No dial tone

•Check installation:

Make sure the base power cord is connected to a working electrical outlet.

Make sure the telephone line cord is connected to the base unit and the wall phone jack.

•Connect another phone to the same modular jack; if the second phone doesn’t work, the problem might be with your wiring or local service.

•The handset may be out of range of the base. Move closer to the base.

•Make sure the battery is properly charged (for 16 hours).

•Ensure the battery pack is installed correctly.

•The handset should beep when you press the talk button, and the charge indicator on the base should be lit when the handset rests in the cradle. If not, the battery may need to be charged.

39

Image 39

Contents DECT6.0 Interference Information Important InformationLicensing Telephone Network InformationREN Number Hearing Aid Compatibility HACInformation for Dect Product FCC RF Radiation Exposure StatementTable of Contents General Product Care Telephone Jack Requirements Parts Checklist for 28225xx2 ModelIntroduction Before You BeginDigital Security System InstallationAvoid areas of excessive dust, moisture and low temperature Important Installation GuidelinesBase Layout Display Icons Handset LayoutInstalling the Handset Batteries Installing the PhoneBase Station Recording the Outgoing Announcement Answering System SetupSetting the Voice Language Answering System ON/OFFSample Outgoing Announcement Remote Access CodeAnnounce Only On/Off Message AlertCall Screening Rings to AnswerDate & Time Handset SettingsProgramming Your Phone Main MenuRingtone Ringer SetupRinger Volume Group MelodySet Alarm Auto TalkRegistration Select Base Tones ON/OFFDeregister Handset Handset Name Handset Display SettingsReset Handset WallpaperArea Code Base SetupDial Mode Handset LanguagePress the Soft Key Left SKL button Answering System Setup via the HandsetDeleting Messages Answering System OperationListening to Your Messages Message PlaybackTo record a Memo at the Base Base Ringer VolumeMemo Recording To delete all old messages with the handsetMemory Full Important InformationRemote Operation Handset Operation Making a CallReceiving a Call Muting the Microphone Changing the Earpiece VolumeRedialing Handset Speaker PhoneMaking Intercom Calls Intercom OperationPaging the Handset Key LockThree Party Conference Call Transfer / ForwardingAfter receiving an external call Caller ID CID Call Waiting Caller IDReceiving CID Records Dialing a CID Number Reviewing CID Records In CID MemoryStoring CID Records in Internal Memory Deleting a CID RecordAs you cannot reformat CID records stored in memory Programming the Phone Book Deleting All CID RecordsNew Entry Edit Entry Dialing from the Phone BookDelete Entry If you choose Save Number Delete AllCall List If you choose Delete EntryIf you choose User Number Battery Safety PrecautionsChanging the Batteries If you choose Delete AllAnswering System Display Messages Display MessagesTelephone Solutions Handset Sound SignalsTroubleshooting Guide Cordless Phone SolutionsMove closer to base. The handset might be out of range Battery SolutionsGeneral Product Care Answering System SolutionsCauses of Poor Reception Accessory InformationWarranty 14 F IndexMemory Model