Telex C-2002 technical manual Supervisor Enable, Alert Programming

Page 35

Remote Control Console

29

7.8.5Dual Function Tone mode Screen

The Dual Function Tone screen is used when operating the C-2002 console with a DSP223 in the 99 Frequency decode mode.

PROG1 – Toggles between Enable/Disabled. PROG3 – Returns to Function tone screen. PROG4 - Returns to the Opening menu screen.

7.9 Supervisor Enable

Dual Tone: DISABLED

Tgl

next back

PROG1 PROG2

PROG3 PROG4

The supervisor function works in a manner similar to crossmute. It allows a single console to take control of all selected lines by disabling transmit on all other attached consoles. See section 4.2.2 for information on the wiring required to support this function. This function should only be enabled on consoles on which a supervisory function is appropriate.

PROG2 - Disables Supervisory Capability.

Super: Enabled

PROG3 - Enables Supervisory Capability.

prev next back

PROG1 PROG2 PROG3 PROG4

PROG4 - Return to top level menus.

7.10 Alert Programming

The following appears if the ALERT button is pressed while the Opening Menu Screen is showing. This screen allows the technician to change the cadence of the alert tones. PROG1 selects between the two alert options. Alert 1 dictates which tone cadence will go out with the ALERT button. Alert 2 dictates which cadence will go out when the ALT button plus ALRT button is configured as a second alert tone.

The PROG2 button scrolls through the available cadencesAlert 1:1000Hz

A1/2 Cad edit back

PROG1 - Selects between Alert 1 and Alert 2.

 

 

 

 

 

PROG1

PROG2

PROG3

PROG4

 

PROG2 – Selects Hi-Lo Warble or Steady Tone.

 

 

PROG3 - Allows editing of the level and frequency for the constant alert tone.

 

 

 

 

PROG4 - return to the Opening Menu Screen.

 

 

 

 

 

 

 

Alert 1:1000Hz

 

 

 

 

 

 

Cadence 1 is a steady programmable frequency.

 

Level Freq

 

back

 

Cadence 2 is a Hi-Lo Warble sound.

 

 

 

 

PROG3

PROG4

 

 

 

PROG1

PROG2

 

7.10.1 Cadence Level Selection

PROG1 - resets the level to the default of 0dBm.

PROG2 - decrements the level by 1 dBm.

PROG3 - increments the level by 1 dBm.

PROG4 - return to the Alert setup menu.

7.10.2 Cadence Frequency Selection

PROG1 - resets the frequency to the default value of 1000Hz. PROG2 - decrements the frequency by 1Hz (min freq of 0Hz). PROG3 - increments the frequency by 1Hz (max freq of 3500Hz). PROG4 - return to Alert Tone setup screen.

DTMF keypad - may be used to program the frequency.

Cad Lvl

= 0dB

back

0dB

dwn

up

PROG1

PROG2

PROG3

PROG4

Cad Freq = 2050

1000H dwn up back

PROG1 PROG2 PROG3 PROG4

Image 35
Contents Model C-2002 Radio Control Console Technical Manual Page Table of Contents Vega’s C-2002 Iii Default Shipping Configuration Introduction Front Panel Controls and IndicatorsCommon Controls and Indicators Rear Panel Ports Rear Panel ConnectionsRear Panel Pinout Rear Panel Connector PinoutsOperation Crossmute Line Setup and DescriptionRelay Contact Closure For Local Control Two-Wire/Four-Wire ModeRX Side Settings Supervisor FunctionTransmit Monitor TX Side SettingsRX Level Adjustment Level AdjustmentsTransmit Side Adjustments Transmit Monitor SetupLine Interface Hardware OverviewC-2002 Console Line Receive Paths Line One/Two Theory of OperationMicrophone Input Paths Audio Output PathsUser I/O Clone Mode Serial Port Power Regulation and Reset ControlSystem Clock Generation Non-Volatile Memory EepromErasing all settings Setup ModeTech Mode Restore Defaults?AUX Opening Display MenuLevel Menu Screen Button Activated Setup ModesOpening menu LAM1-S 7sec -10dBm dur lvl S/U back Line 1 level adjustLn1 Min Rx lvl -60dB 60dB dwn Back10db dwn Back Main level adjust MIC Spkr TX backMain Mic adjust Mute Level = -10dBSystem Settings Screen Target Not Found Dump back Main tone Adjust Dtmf Tone BackWorking… Please WaitOff Dtmf Keypad Enable TglDtmf Hold = 500msec 500ms dwn up back 100/100Level 10/0/-20 Guard FTn Hold back Tone Settings Lvl Freq Dur backDtmf RX Hold Sec Edit Next Duration 130/200 Guard Hold Back AUX Input Enabled TglbackAUX Input Enable Grd&Hld Freq= 2175Hz Prev next backNew PIN System Settings PIN Txdel next backPIN Setup New TX Delay 300msecAlphanumeric Function-Line Setup Line/F-Tone Selection Screen L1 F? Back? F1 Back RampartLine Tone/Local Screen Mute Button Function Tone Parameter Screen Alert Programming Supervisor EnableMonitor Programming Screen Section Parameter Default Programmed Vega’s C-2002 Remote Control Console C-2002 Main Board, P/N C-2002 Top Assembly, P.NSchematic Bill of Material, component layout Technical DocumentationPage Page Page Page Page Page Page Page PCB ASSY, C-2002 Main Board QTY Type Description Designator Conn SMT 40 PIN Type Description Designator Page BNSFRDCKeypad.sch-1 Fri Mar 22 131105 PCB ASSY, Bnsf RDC Keypad Board Page Page Doug Ehlers Factory Service Center Telex Communications, Inc Warranty, Service, Repair, and CommentsWarranty Limited Front panel controls Specifications