Telex C-2002 technical manual System Settings Screen

Page 24

18

Vega’s C-2002

PROG3 - Decrements the level setting by 1 dB (minimum of -60dB).

PROG4 - Saves the current level setting and returns to the SPKR menu.

7.3.2.3 Output Level Screens

Entering the TX output level screen allows for setting output levels.

7.3.2.3.1 TX Output Level

The TX output level is adjusted as shown on the display. This is an overall output gain control for the line. It can be used to make small adjustments to the line level performance. The typical value is 0 dB.

PROG1 - Resets level setting to default of 0dBm.

PROG2 - Increments the level setting by 1 dBm (max of +10dBm). PROG3 - Decrements the level setting by 1 dBm (min of -10dBm). PROG4 - Saves the current level setting and returns to the Line Level

Setting screen.

TX Level

0dB

back

0dBm

dwn

up

PROG1

PROG2

PROG3

PROG4

7.4 System Settings Screen

This menu is entered by selecting PROG2 from the PROGRAMMING MODE menu. Once in this mode there are 5 different menus that can be entered. Each is brought up sequentially by pressing the PROG3 button labeled next on the display.

PROG1 - Clock Set Routines.

PROG2 - Dump setup memory to another console. PROG3 - Next Menu.

PROG4 - Return to Opening Menu.

7.4.1Clock Settings Screen

System Settings

Clk Dump next back

PROG1 PROG2 PROG3 PROG4

The top line of the Clock Settings Screen holds the current time and whether the clock is set for 12 or 24 hour display. Note: The clock can also be accessed by pressing MUTE-F6-C on the keypad. This goes directly to the clock setup screen shown at the right. This bypasses the PIN number entry (if enabled) and allows a user who would normally have no access to the setup mode to access and update the clock.

PROG1 - Allows editing the minutes and hours. PROG2 - Selects between AM and PM. PROG3 - Selects between 12 and 24 hr time.

PROG4 - Saves the current settings and returns to the Opening Menu.

Clock 11:19AM 12hr Edit A/P 12/24 back

PROG1 PROG2 PROG3 PROG4

7.4.1.1 Clock Edit Screen

PROG1 - Go to Hours Settings Screen. PROG3 - Go to Minutes Settings Screen. PROG4 - Return to System Settings Screen.

7.4.1.1.1 Clock Hours Screen

PROG1 - Set Hours to 12. PROG2 - Decrease Hours by 1. PROG3 - Increase Hours by 1.

PROG4 - Return to Clock Settings Screen.

7.4.1.1.2 Clock Minutes Screen

PROG1 - Set Minutes to 0. PROG2 - Decrease Minutes by 1. PROG3 - Increase Minutes by 1.

PROG4 - Return to Clock Settings Screen.

Clock 11:19AM

12hr

Hours

Mins

back

PROG1 PROG2

PROG3

PROG4

Hours = 11

12 dwn up back

PROG1 PROG2 PROG3 PROG4

Mins = 19

0 dwn up back

PROG1 PROG2 PROG3 PROG4

Image 24
Contents Model C-2002 Radio Control Console Technical Manual Page Table of Contents Vega’s C-2002 Iii Default Shipping Configuration Introduction Controls and Indicators Common Controls and IndicatorsFront Panel Rear Panel Connections Rear Panel PortsRear Panel Connector Pinouts Rear Panel PinoutOperation Line Setup and Description CrossmuteTwo-Wire/Four-Wire Mode RX Side SettingsSupervisor Function Relay Contact Closure For Local ControlTX Side Settings Transmit MonitorLevel Adjustments Transmit Side AdjustmentsTransmit Monitor Setup RX Level AdjustmentHardware Overview C-2002 ConsoleLine Interface Theory of Operation Microphone Input PathsAudio Output Paths Line Receive Paths Line One/TwoClone Mode Serial Port Power Regulation and Reset Control System Clock GenerationNon-Volatile Memory Eeprom User I/OSetup Mode Tech ModeRestore Defaults? Erasing all settingsOpening Display Menu AUXButton Activated Setup Modes Opening menuLevel Menu Screen Line 1 level adjust Ln1 Min Rx lvl -60dB60dB dwn Back LAM1-S 7sec -10dBm dur lvl S/U backMain level adjust MIC Spkr TX back Main Mic adjustMute Level = -10dB 10db dwn BackSystem Settings Screen Main tone Adjust Dtmf Tone Back Working…Please Wait Target Not Found Dump backDtmf Keypad Enable Tgl Dtmf Hold = 500msec 500ms dwn up back100/100 OffTone Settings Lvl Freq Dur back Dtmf RX Hold Sec Edit NextLevel 10/0/-20 Guard FTn Hold back AUX Input Enabled Tglback AUX Input EnableGrd&Hld Freq= 2175Hz Prev next back Duration 130/200 Guard Hold BackSystem Settings PIN Txdel next back PIN Setup NewTX Delay 300msec New PINAlphanumeric Function-Line Setup L1 F? Back ? F1 BackRampart Line/F-Tone Selection ScreenLine Tone/Local Screen Mute Button Function Tone Parameter Screen Supervisor Enable Alert ProgrammingMonitor Programming Screen Section Parameter Default Programmed Vega’s C-2002 Remote Control Console C-2002 Top Assembly, P.N Schematic Bill of Material, component layoutTechnical Documentation C-2002 Main Board, P/NPage Page Page Page Page Page Page Page PCB ASSY, C-2002 Main Board QTY Type Description Designator Conn SMT 40 PIN Type Description Designator Page BNSFRDCKeypad.sch-1 Fri Mar 22 131105 PCB ASSY, Bnsf RDC Keypad Board Page Page Doug Ehlers Warranty, Service, Repair, and Comments Warranty LimitedFactory Service Center Telex Communications, Inc Specifications Front panel controls