Siemens RS232, M101 operating instructions What happens if, Place of installation

Page 20

21.4.99

gigam101.fm5

Gigaset V.24 Adapter dt/eng:A30853-X400-B104-3-74D1

What happens if...

What happens if...

If a malfunction occurs, check the following points:

●Both stations are powered.

●The cable connections to the connected devices are fully in- serted and screwed in.

●The stations are not too far apart and are there are no large parts of buildings in between.

●Registration was successful.

●The lokalen Station operating mode is "AT commands, local" or "AVM/Eumax commands, local".

or:

●The lokalen Station operating mode is "Direct connection" and you have set the direct connection transmission param- eters in your communication software.

If the malfunction still occurs after checking all the above points, reset both Gigaset M101 Data units to the factory defaults, see page 19.

If the malfunction persists, call the hotline at 0180 5 333 220.

Internet: www.siemens.de/gigaset

Notes on installation and operation

Place of installation

There must be a 220/230 V AC 50 Hz power socket in the vicin- ity.

The Gigaset M101 Data should not be installed in the immediate vicinity of other electronic devices, such as hi-fi systems, office equipment or microwave ovens, otherwise there is a risk of mu- tual interference.

Place the Gigaset M101 Data unit on a level, non-slip surface. The device feet do not normally leave any unsightly marks. How- ever, in view of the many different varnishes and polishes cur- rently used for furniture, the possibility of marks being left can- not be ruled out.

Radio communication between Basis and Teilnehmer is based on the DECT standard. The Gigaset M101 Data complies fully with the relevant European directives. Should you nevertheless experience sound or picture distortion with your satellite signal receiving equipment, please get in touch with your dealer to have it tested for shielding faults.

Depending on the ambient conditions, the maximum radio range between the local station and the Partnerstation is ap- prox. 300 m outdoors and approx. 50 m indoors.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Gigaset M101 Data Registering a Gigaset M101 Data Setting the operating mode Overview Front BackContents Contents Approval and conformity Introduction What is a Gigaset M101 Data? Safety precautionsChecking the contents of the package Putting into servicePutting into service Putting into service Installing the program package Prerequisites for installationInstallation Check installation is successfulPutting into service Connecting stations Initial configuration Initial configurationConfiguration program options Configuration program optionsStarting the configuration program GeneralLower section radio connection Configuration program options Connection tabUpper section connecting to the PC Configuration program options Operating mode tab Setting the operating modeChanging a name Special settings for Direct connection modeLocal station tab Changing a station type Registering an Teilnehmer station Click RegisterPartner station tab De-registering a Teilnehmer stationChanging the name Changing the PINLEDs and buttons LEDs and buttonsBoth button functions LED 1 Gigaset M101 Data statusWhat happens if Place of installationWhat happens if Technical data Temperature and ambient conditionsSignals to V.24 interfaceName Based on Ccitt Meaning Std. Pin Assign Pin plug based on Ccitt Pole SubD socketWhy set a mode? Technical background Tips & tricks, settings Tips & tricks, settingsOperating from a local station with two remote stations TeilnehmerPC PC direct cable connection via RS232/V.24 interface Setting the direct connection to the correct baud rate Set direct cable connection parameters Activate Hardware under Use flow control in the Settings Tips & tricks, settings Tips & tricks, settings Tips & tricks, settings Sharing files PC PC direct cable connection problems examples MAC and other operating systemsMeaning of lokale Station and Partnerstation Meaning of Basis and TeilnehmerUpdates and news on the Internet SupportConfiguration management Fault Cause Problems with application programs Fault CauseFault Cause Solution Hardware problems PC, modem, Isdn TA Fault Cause SolutionElsa TagGo2000 / Isdn con Acer Isdn T30 terminalMiscellaneous Fault Cause Solution With Elsa Microlink 56k

M101, RS232 specifications

The Siemens RS232 M101 is a notable communication interface device that is widely utilized in industrial applications for data transfer between machines and control systems. Its introduction marked a significant advancement in serial communication technology, allowing for efficient and reliable connectivity in a variety of environments.

One of the primary features of the Siemens RS232 M101 is its adherence to the RS232 standard, which defines the protocols for serial communication. This standard ensures compatibility with a wide range of devices, making it versatile for use in various applications. The M101 facilitates point-to-point communication, enabling direct data exchange between two devices, such as computers, programmable logic controllers (PLCs), and sensors, which is crucial for real-time monitoring and control processes.

The technology behind the M101 includes its ability to support baud rates of up to 115,200 bps, enabling high-speed data transfer. This capability is essential in environments where timely data exchange is critical, such as manufacturing and automation sectors. The device also features a robust design that ensures reliable operation even in challenging industrial conditions, including temperature variations and electromagnetic interference.

Additionally, the Siemens RS232 M101 supports flow control mechanisms such as RTS/CTS (Request to Send/Clear to Send) and XON/XOFF (software flow control), which help manage data transmission effectively. By preventing data loss due to buffer overruns, these technologies enhance the integrity of data being transmitted, providing users with confidence in the reliability of their systems.

The M101 interface is compatible with a variety of operating systems, which simplifies integration into existing setups. Furthermore, it includes diagnostic LEDs that indicate communication status, making troubleshooting straightforward and user-friendly.

In summary, the Siemens RS232 M101 is a pivotal component in industrial communication, characterized by its adherence to RS232 standards, high-speed data transfer capabilities, robust build, and effective flow control mechanisms. Its widespread compatibility and user-friendly features make it a valuable tool for ensuring seamless communication between different systems in industrial applications. By facilitating reliable data exchange, the M101 enhances operational efficiency and contributes to the overall effectiveness of automated processes.
Top Page Image Contents