VTech LS6195-17, LS6195-15, LS6195-16 Handset battery charging, Displays Put in charger

Page 8

Getting started

Handset battery charging

Once you have installed the battery, the screen indicates the battery status (see the table below). If necessary, place the handset in the telephone base to charge the battery. For best performance, keep the handset in the telephone base when not in use. The battery is fully charged after 11 hours of continuous charging. See the table on page 59 for battery operating times.

If the screen is blank or displays Put in charger, you need to charge the handset without interruption for at least 30 minutes to give the handset enough charge to use the telephone for a short time. When the battery is low, the handset displays Low battery along with a flashing icon. If you are on a call in low battery mode, the handset plays short beeps to alert you.

The following table summarizes the battery charge indicators and actions to take.

 

 

Battery indicators

Battery status

Action

The screen is blank, or

The battery has no or very

Charge without interruption

displays Put in charger and

little charge. The handset

(about 30 minutes).

 

 

flashes.

cannot be used.

 

 

 

 

 

 

 

 

 

 

The screen displays

The battery has enough

Charge without interruption

Low battery and

 

 

 

flashes.

charge to be used for a

(about 30 minutes).

 

 

 

 

 

 

 

 

 

short time.

 

 

 

 

 

 

 

 

 

 

The screen displays

The battery is charged.

To keep the battery charged,

HANDSET X.

 

place it in the telephone

 

 

 

 

 

 

 

 

base when not in use.

 

 

 

 

 

 

 

 

 

If you place the handset in the telephone base without installing a battery, the screen displays No battery.

After you install your telephone or power returns following a power outage, the handset will prompt you to set the date and time. For instructions, see Set date and time on page 13.

To skip setting the date and time, press OFF/CANCEL.

Date: MM/DD/YY

ECO

ANS ON

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Complete user’s manual Registration Product newsTable of contents Index Parts checklist Getting startedTelephone base installation Handset battery installation This Side UP / CE Côté Vers LE HautHandset battery charging Displays Put in chargerTelephone base layout VOLMute Find Handset Volume Handset layoutINT Using the menu To enter the handset menuTelephone base settings Handset ringer volumeTelephone base ringer volume Press Select to choose Ringer volumeTelephone settings Quiet modeTo set the quiet mode duration To turn off the quiet modeSet date and time Press Select to select LCD language LCD languageBase LCD language Voicemail number To set the voicemail numberKey tone Clear voicemail indicatorsTo manually turn off the new voicemail indicators Dial mode Home area codeAuto answer Using the handset Using the telephone baseTelephone operation Make a callVolume control Answer a callEnd a call Handset speakerphoneMute Call waitingTemporary ringer silencing To silence the handset ringerTemporary tone dialing Chain dialingCheck voicemail Find handsetWebsite To start the paging toneTo delete a redial number RedialTo review and dial a redial number Transfer a call To join a call Multiple handset useJoin a call in progress Intercom Answer an incoming call during an intercom callHS 1 is calling HS X is callingCall transfer using intercom Directory About the directoryPress Delete to erase a digit Add a directory entryAdd contact Enter number Review directory entries Alphabetical searchDial a directory entry Edit a directory entryDelete a directory entry Delete contact?Reassign a speed dial slot Speed DialAssign a speed dial slot Dial a speed dial number Delete a speed dial entryInformation about caller ID with call waiting Caller IDAbout caller ID Caller ID log Memory matchEntries in CID XXX for a few seconds Missed call indicatorReview the caller ID log View dialing options Dial a caller ID log entry Save a caller ID log entry to the directoryDelete caller ID log entries Caller ID log screen messagesTo delete one entry Caller ID log onAnswering system settings Answering systemAnnouncement Record your own announcementDelete your announcement Answer on/offCall screening Number of rings00 to Remote access codeMessage alert tone Recording time Using the answering system and voicemail together Answering system operationAnswering system and voicemail Handset, see To play messages on the handset onMessage capacity New message indicationTo screen a call at the telephone base Options while a message is being recordedCall intercept Temporarily turn off the message alert toneMessage playback To play messages at the telephone baseOptions during playback To play messages on the handsetDelete all old messages Record, play and delete memosDelete all msg? To record a memoRemote access Command DescriptionAppendix Expand your telephone systemAdd and register a handset To register a handsetDeregister handsets To deregister all handsetsScreen messages Appendix Handset and telephone base indicators Telephone base lightsHandset icons Telephone base iconsBattery Operation Operating timeTroubleshooting My telephone doesn’t work at allCannot dial out Appendix Hear other calls while using my phone My calls cut in and out while I’m using my cordless handset My telephone does not receive caller ID when on a call System announces Time and day not set Cannot retrieve voicemail messages Important safety instructions Operating range Precautions for users of implanted cardiac pacemakersECO mode Maintenance About cordless telephonesRbrc seal FCC, Acta and IC regulations FCC PartFCC Part 68 and Acta Industry CanadaLimited warranty What does this limited warranty cover?How do you get warranty service? Technical specifications Index Index All rights reserved. Version 1 09/12 91-006037-010-100
Top Page Image Contents