VTech VT 1962 manual Replace the battery case cover by sliding the cover upwards

Page 10

REPLACING THE BATTERY PACK

Follow the steps below:

1.Remove the battery case cover by pressing on the ridged lines and sliding downward.

Press and Slide

Downward

2.Discard the old battery pack. Don't put the old battery pack in a trash compactor or a fire - it could burst.

3.Place the new battery pack in its housing with the metal contacts facing down.

Place the new battery pack into the battery compartment

Please note the correct position of the battery pack when changing battery

4.Replace the battery case cover by sliding the cover upwards.

Slide in the battery cover

5.If the new battery pack is not already charged, place the Handset in the cradle of the Base Unit to allow it to charge for 16 hours.

CAUTION:

To reduce the risk of fire or injury, read and follow the Instructions:

1.Use only VTECH rechargeable battery pack.

2.Do not dispose of the battery in a fire. The cell may explode.

IMPORTANT: Do not dispose of this battery into household garbage. For information on recycling or proper disposal, consult your local solid waste collection or disposal organization.

3.Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

10

Image 10

Contents Introduction Special Features MHz OperationParts Check List FCC and IC Regulations FCC PartIC Industry Canada This telephone is registered for use in CanadaFCC and IC Regulations Important Safety Instructions Read and understand all instructionsIf the product exhibits a distinct change in performance To Charge The Battery Pack Replacing the Battery PackCharging The Handset Battery Pack Its Impossible To Over-Charge The Battery PackReplace the battery case cover by sliding the cover upwards Power Backup Spare Battery ChargerInstallation Replacing a Drained Handset batteryRbrctm Seal The Rbrcr Seal on the nickel-cadmium battery Setting the Tone/Pulse Switch Setting Up Your VTAC Power Adapter Getting StartedConnect Telephone Line Cord Using The Wall Mount Adapter Wall MountingLCD Display LCD Display MessagesHandset Features Handset LayoutBase Unit Features Base Unit LayoutQuick Reference Guide CID Caller ID Using RedialMemory Dialing Speed Dialing To exit press OFFBasic Operation Call Waiting Switching calls using FlashAdvanced Functions Temporary ToneChecking The Ringer Type Changing Ringer TypesTurning Off The Ringer To turn off the ringer do the followingCLR/DEL Key Function Advanced DialingIf programming is unsuccessful the unit will display Memory DialingDialing From Memory Press Phone to get a lineDeleting Stored Numbers Changing Stored NumbersStoring Special Codes Word About Caller ID CID CID-CALLER IDCall Waiting Caller ID Type II CID Receiving and Storing CallsTransmission Error Special Message Indicators Out of Area CallsPrivate Calls Reviewing Numbers Reviewing CID RecordsDeleting Numbers Answering System Program- ming Overview Answering System SetupDefault Answering System Settings Set Outgoing Message OGMSecurity code default setting is Day and TimeSet Audible Message Alert Set Announce OnlySet Number of Rings Set Base Ringer On/OffBase ringer can be turned on or OFF Listening to Messages / Memos Answering System OperationsLeaving a Message Incoming Message Saving MessagesDeleting Messages Turning the Answering MachineCheck Current Day and Time Changing Speaker VolumeCall Screening Changing Playback SpeedMemory Full Power Failure Flashing number LED displays What it meansYou have no new messages Remote Operation of Answering System Playing Messages RemotelyStop Message Playback Repeat Messages During PlaybackSkip Messages During Playback Memo RecordingExiting Remote Operation Additional Operating Tips Operation Headset OperationBelt Clip Maintenance Case of Difficulty Handset Does Not Ring When You Receive a CallYou Hear Other Calls While Using Your Phone Phone Doesnt Work At AllCommon Cure For Electronic Equipment To the original purchaser only ONE Year Warranty StatementAny defect in material or workmanship At our option, repair or replace your unitWhat does OUR Warranty not COVER? Crystal Controlled Dual PLL Synthesizer Technical SpecificationsHandset 295 grams Base 470 grams Table of Contents Issue