VTech VT 1962 manual Connect Telephone Line Cord

Page 14

GETTING STARTED

Connect Telephone Line Cord

Plug one end of the telephone cord into a wall jack and the other end into the back of the Base Unit.

Check for a dial tone. After the battery pack is charged, rotate the Base Unit antenna to an upright position. Pick up the Handset and press PHONE . "PHONE ON" will appear on the LCD, and you will hear a dial tone. If not, see 'IN CASE OF DIFFICULTY' on page 46.

Fill in the telephone number card on the Base Unit.

			ANSWER
		MEMO	ON/OFF
CHARGING		SPARE	IN USE
CHARGING		BATTERY	IN USE
MAIL BOX1	MAIL BOX2		MAIL BOX3
	PLAY/STOP
DELETE	TIME/SET	SELECT	MENU
REPEAT/SLOW	SKIP/QUICK		VOLUME
	PAGE

CAUTION:

1.Never install telephone wiring during a lightning storm.

2.Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

3.Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

4.Use caution when installing or modifying telephone lines.

14

Image 14

Contents Introduction Special Features MHz OperationParts Check List FCC and IC Regulations FCC PartIC Industry Canada This telephone is registered for use in CanadaFCC and IC Regulations Important Safety Instructions Read and understand all instructionsIf the product exhibits a distinct change in performance To Charge The Battery Pack Replacing the Battery PackCharging The Handset Battery Pack Its Impossible To Over-Charge The Battery PackReplace the battery case cover by sliding the cover upwards Power Backup Spare Battery ChargerInstallation Replacing a Drained Handset batteryRbrctm Seal The Rbrcr Seal on the nickel-cadmium battery Setting the Tone/Pulse Switch Setting Up Your VTAC Power Adapter Getting StartedConnect Telephone Line Cord Using The Wall Mount Adapter Wall MountingLCD Display LCD Display MessagesHandset Features Handset LayoutBase Unit Features Base Unit LayoutQuick Reference Guide CID Caller ID Using RedialMemory Dialing Speed Dialing To exit press OFFBasic Operation Call Waiting Switching calls using FlashAdvanced Functions Temporary ToneChecking The Ringer Type Changing Ringer TypesTurning Off The Ringer To turn off the ringer do the followingCLR/DEL Key Function Advanced DialingIf programming is unsuccessful the unit will display Memory DialingDialing From Memory Press Phone to get a lineStoring Special Codes Changing Stored NumbersDeleting Stored Numbers Word About Caller ID CID CID-CALLER IDCall Waiting Caller ID Type II CID Receiving and Storing CallsPrivate Calls Special Message Indicators Out of Area CallsTransmission Error Reviewing Numbers Reviewing CID RecordsDeleting Numbers Answering System Program- ming Overview Answering System SetupDefault Answering System Settings Set Outgoing Message OGMSecurity code default setting is Day and TimeSet Audible Message Alert Set Announce OnlyBase ringer can be turned on or OFF Set Base Ringer On/OffSet Number of Rings Listening to Messages / Memos Answering System OperationsLeaving a Message Incoming Message Saving MessagesDeleting Messages Turning the Answering MachineCheck Current Day and Time Changing Speaker VolumeCall Screening Changing Playback SpeedMemory Full Power Failure You have no new messages LED displays What it meansFlashing number Remote Operation of Answering System Playing Messages RemotelyStop Message Playback Repeat Messages During PlaybackSkip Messages During Playback Memo RecordingExiting Remote Operation Additional Operating Tips Belt Clip Headset OperationOperation Maintenance Case of Difficulty Handset Does Not Ring When You Receive a CallYou Hear Other Calls While Using Your Phone Phone Doesnt Work At AllCommon Cure For Electronic Equipment To the original purchaser only ONE Year Warranty StatementAny defect in material or workmanship At our option, repair or replace your unitWhat does OUR Warranty not COVER? Handset 295 grams Base 470 grams Technical SpecificationsCrystal Controlled Dual PLL Synthesizer Table of Contents Issue