VTech VT 1962 manual Wall Mounting, Using The Wall Mount Adapter

Page 15

WALL MOUNTING

Using The Wall Mount Adapter

1.Choose a spot near an electrical outlet and a telephone jack.

You phone requires a modular telephone jack and a standard electrical outlet (120v AC). The power cord is six feet long; make sure there is an electrical outlet within reach of the Base Unit. The outlet should not be controlled by a wall switch. If the switch is ever turned off, the phone will not operate.

2.Position the wall mount bracket on the Base.

Line up the tabs on the wall mount adaptor with the holes on the bottom of the Base (Figure 1). Snap the wall mount bracket firmly in place.

3.Mount the Base on the wall.

Position the Base so the mounting studs will fit into the holes on the bottom of the Base. Position the power cord to extend down the wall the phone is to be mounted on. Slide the Base down on the mounting studs until it locks into place.

4.Connect the telephone line cord.

The telephone line cord has a snap-in plug at each end. Insert one of the plugs into the jack on the bottom of the Base. Insert the other end of the plug into the wall jack.

5.Plug the AC adaptor into an electrical outlet and the DC connector into the power jack located on the back of the Base Unit .

TONE

PULSE

Figure 1

DELETE

TIME/SET SELECTMENU

REPEAT/SLOW

SKIP/QUICK

VOLUME

PAGE

Figure 2

15

Image 15

Contents Introduction MHz Operation Special FeaturesParts Check List FCC Part FCC and IC RegulationsThis telephone is registered for use in Canada IC Industry CanadaFCC and IC Regulations Read and understand all instructions Important Safety InstructionsIf the product exhibits a distinct change in performance Its Impossible To Over-Charge The Battery Pack Replacing the Battery PackCharging The Handset Battery Pack To Charge The Battery PackReplace the battery case cover by sliding the cover upwards Replacing a Drained Handset battery Spare Battery ChargerInstallation Power BackupRbrctm Seal The Rbrcr Seal on the nickel-cadmium battery Getting Started Setting Up Your VTAC Power Adapter Setting the Tone/Pulse SwitchConnect Telephone Line Cord Wall Mounting Using The Wall Mount AdapterLCD Display Messages LCD DisplayHandset Layout Handset FeaturesBase Unit Layout Base Unit FeaturesQuick Reference Guide To exit press OFF Using RedialMemory Dialing Speed Dialing CID Caller IDBasic Operation Temporary Tone Switching calls using FlashAdvanced Functions Call WaitingTo turn off the ringer do the following Changing Ringer TypesTurning Off The Ringer Checking The Ringer TypeAdvanced Dialing CLR/DEL Key FunctionPress Phone to get a line Memory DialingDialing From Memory If programming is unsuccessful the unit will displayChanging Stored Numbers Deleting Stored NumbersStoring Special Codes Receiving and Storing Calls CID-CALLER IDCall Waiting Caller ID Type II CID Word About Caller ID CIDSpecial Message Indicators Out of Area Calls Transmission ErrorPrivate Calls Reviewing CID Records Reviewing NumbersDeleting Numbers Set Outgoing Message OGM Answering System SetupDefault Answering System Settings Answering System Program- ming OverviewDay and Time Security code default setting isSet Announce Only Set Audible Message AlertSet Base Ringer On/Off Set Number of RingsBase ringer can be turned on or OFF Saving Messages Answering System OperationsLeaving a Message Incoming Message Listening to Messages / MemosTurning the Answering Machine Deleting MessagesChanging Playback Speed Changing Speaker VolumeCall Screening Check Current Day and TimeMemory Full Power Failure LED displays What it means Flashing numberYou have no new messages Playing Messages Remotely Remote Operation of Answering SystemMemo Recording Repeat Messages During PlaybackSkip Messages During Playback Stop Message PlaybackExiting Remote Operation Additional Operating Tips Headset Operation OperationBelt Clip Maintenance Phone Doesnt Work At All Handset Does Not Ring When You Receive a CallYou Hear Other Calls While Using Your Phone Case of DifficultyCommon Cure For Electronic Equipment At our option, repair or replace your unit Warranty StatementAny defect in material or workmanship To the original purchaser only ONE YearWhat does OUR Warranty not COVER? Technical Specifications Crystal Controlled Dual PLL SynthesizerHandset 295 grams Base 470 grams Table of Contents Issue