VTech VT 1962 manual Basic Operation

Page 21

BASIC OPERATION

Making Calls

You can make calls directly from the Handset whether you are at the Base or away from it.

NOTE: There are two different ways to dial a number:

1.Press the PHONE key and wait for dial tone. Then dial the number you want.

Or

2.Enter the number onto the display first, then press the PHONE key. This will dial the number that is displayed on the LCD after 2 seconds. See "ADVANCED DIALING" on Page 24.

If you make a mistake when dialing, press OFF to hang up, then press the PHONE key to get the dial tone again.

Disconnecting

To end a call, either place the Handset back in the Base, or press OFF on the Handset.

ANSWERING Calls

When the Handset rings, press any key other than OFF, MUTE or the VOLUME keys to answer your call.

Volume Controls

The volume controls for the Handset are located on the side of the unit. Press the (up) or (down) keys to increase or decrease the volume. Holding either key down will continuously change the volume setting. The earpiece volume level indicator on the LCD will change accordingly. There are four volume levels.

FLASH

You can use your VT 1962 cordless phone with services such as Call Waiting. Simply press the PHONE key to FLASH the line.

REDIAL

To REDIAL the last number you dialed, press the PHONE key, then press REDIAL . The phone will automatically dial the number. The number will be shown on the display.

Clearing The Display

The display can be cleared by pressing and holding the CLR/DEL key down until the display clears.

MUTE

Press MUTE during conversation to disable the Handset microphone.

Press MUTE again to return to normal operation.

Ringer Mute

Press MUTE during incoming ringing to disable the ringer for the duration of the call.

HOLD

Press HOLD to place an active call on hold.

The LCD will display CALL ON HOLD.

Press HOLD again to return to the call.

PAGE/HANDSET Locator

To page from the Base Unit, press PAGE .

The LCD will display BASE PAGING HANDSET.

To cancel the page, either press PAGE again on the Base Unit, or press OFF on the Handset.

21

Image 21
Contents Introduction MHz Operation Special FeaturesParts Check List FCC Part FCC and IC RegulationsThis telephone is registered for use in Canada IC Industry CanadaFCC and IC Regulations Read and understand all instructions Important Safety InstructionsIf the product exhibits a distinct change in performance Charging The Handset Battery Pack Replacing the Battery PackTo Charge The Battery Pack Its Impossible To Over-Charge The Battery PackReplace the battery case cover by sliding the cover upwards Installation Spare Battery ChargerPower Backup Replacing a Drained Handset batteryRbrctm Seal The Rbrcr Seal on the nickel-cadmium battery AC Power Adapter Setting Up Your VTSetting the Tone/Pulse Switch Getting StartedConnect Telephone Line Cord Wall Mounting Using The Wall Mount AdapterLCD Display Messages LCD DisplayHandset Layout Handset FeaturesBase Unit Layout Base Unit FeaturesQuick Reference Guide Memory Dialing Speed Dialing Using RedialCID Caller ID To exit press OFFBasic Operation Advanced Functions Switching calls using FlashCall Waiting Temporary ToneTurning Off The Ringer Changing Ringer TypesChecking The Ringer Type To turn off the ringer do the followingAdvanced Dialing CLR/DEL Key FunctionDialing From Memory Memory DialingIf programming is unsuccessful the unit will display Press Phone to get a lineChanging Stored Numbers Deleting Stored NumbersStoring Special Codes Call Waiting Caller ID Type II CID CID-CALLER IDWord About Caller ID CID Receiving and Storing CallsSpecial Message Indicators Out of Area Calls Transmission ErrorPrivate Calls Reviewing CID Records Reviewing NumbersDeleting Numbers Default Answering System Settings Answering System SetupAnswering System Program- ming Overview Set Outgoing Message OGMDay and Time Security code default setting isSet Announce Only Set Audible Message AlertSet Base Ringer On/Off Set Number of RingsBase ringer can be turned on or OFF Leaving a Message Incoming Message Answering System OperationsListening to Messages / Memos Saving MessagesTurning the Answering Machine Deleting MessagesCall Screening Changing Speaker VolumeCheck Current Day and Time Changing Playback SpeedMemory Full Power Failure LED displays What it means Flashing numberYou have no new messages Playing Messages Remotely Remote Operation of Answering SystemSkip Messages During Playback Repeat Messages During PlaybackStop Message Playback Memo RecordingExiting Remote Operation Additional Operating Tips Headset Operation OperationBelt Clip Maintenance You Hear Other Calls While Using Your Phone Handset Does Not Ring When You Receive a CallCase of Difficulty Phone Doesnt Work At AllCommon Cure For Electronic Equipment Any defect in material or workmanship Warranty StatementTo the original purchaser only ONE Year At our option, repair or replace your unitWhat does OUR Warranty not COVER? Technical Specifications Crystal Controlled Dual PLL SynthesizerHandset 295 grams Base 470 grams Table of Contents Issue