VTech VT 1962 Special Message Indicators Out of Area Calls, Private Calls, Transmission Error

Page 28

CID-CALLER ID

However, when you dial directly from CID memory, only the last 7 digits of the received telephone number will be used. Consequently, you would actually dial this:

The VT 1962 was designed to accommodate this situation. If you need to temporarily add a long dlstance prefix and /or area code (such as 1503) before the CID number, do the following:

Beginning from the standby mode, key in the necessary digits. Your display will look like this:

Then, to temporarily add the last 7 digits only from a CID memory, press CID .

Using the (*) and (#) keys, scroll through the received calls to locate the number you wish to dial.

Once you have located the number you wish to dial, simply press PHONE . The last seven digits will be added to the numbers already in the LCD, and the whole number shown below will be automatically dialed.

Special Message Indicators Out of Area Calls

If for any reason the telephone number of the caller is unavailable, or if the caller is outside the CID service area, the message UNAVAILABLE is displayed on the LCD.

"Private" Calls

If the caller has exercised the option to block his or her number from being sent, then the display will show

PRIVATE.

Transmission Error

If an error is detected, then the CID information is incomplete and will not be displayed. "TRANSMISSION ERROR" will be displayed on the LCD screen.

The occasional appearance of "TRANSMISSION ERROR" on your display does not indicate a problem with your unit or your telephone line. However, if this appears frequently, you may want to notify your telephone company.

28

Image 28
Contents Introduction Special Features MHz OperationParts Check List FCC and IC Regulations FCC PartIC Industry Canada This telephone is registered for use in CanadaFCC and IC Regulations Important Safety Instructions Read and understand all instructionsIf the product exhibits a distinct change in performance Replacing the Battery Pack Charging The Handset Battery PackTo Charge The Battery Pack Its Impossible To Over-Charge The Battery PackReplace the battery case cover by sliding the cover upwards Spare Battery Charger InstallationPower Backup Replacing a Drained Handset batteryRbrctm Seal The Rbrcr Seal on the nickel-cadmium battery Setting Up Your VT AC Power AdapterSetting the Tone/Pulse Switch Getting StartedConnect Telephone Line Cord Using The Wall Mount Adapter Wall MountingLCD Display LCD Display MessagesHandset Features Handset LayoutBase Unit Features Base Unit LayoutQuick Reference Guide Using Redial Memory Dialing Speed DialingCID Caller ID To exit press OFFBasic Operation Switching calls using Flash Advanced FunctionsCall Waiting Temporary ToneChanging Ringer Types Turning Off The RingerChecking The Ringer Type To turn off the ringer do the followingCLR/DEL Key Function Advanced DialingMemory Dialing Dialing From MemoryIf programming is unsuccessful the unit will display Press Phone to get a lineDeleting Stored Numbers Changing Stored NumbersStoring Special Codes CID-CALLER ID Call Waiting Caller ID Type II CIDWord About Caller ID CID Receiving and Storing CallsTransmission Error Special Message Indicators Out of Area CallsPrivate Calls Reviewing Numbers Reviewing CID RecordsDeleting Numbers Answering System Setup Default Answering System SettingsAnswering System Program- ming Overview Set Outgoing Message OGMSecurity code default setting is Day and TimeSet Audible Message Alert Set Announce OnlySet Number of Rings Set Base Ringer On/OffBase ringer can be turned on or OFF Answering System Operations Leaving a Message Incoming MessageListening to Messages / Memos Saving MessagesDeleting Messages Turning the Answering MachineChanging Speaker Volume Call ScreeningCheck Current Day and Time Changing Playback SpeedMemory Full Power Failure Flashing number LED displays What it meansYou have no new messages Remote Operation of Answering System Playing Messages RemotelyRepeat Messages During Playback Skip Messages During PlaybackStop Message Playback Memo RecordingExiting Remote Operation Additional Operating Tips Operation Headset OperationBelt Clip Maintenance Handset Does Not Ring When You Receive a Call You Hear Other Calls While Using Your PhoneCase of Difficulty Phone Doesnt Work At AllCommon Cure For Electronic Equipment Warranty Statement Any defect in material or workmanshipTo the original purchaser only ONE Year At our option, repair or replace your unitWhat does OUR Warranty not COVER? Crystal Controlled Dual PLL Synthesizer Technical SpecificationsHandset 295 grams Base 470 grams Table of Contents Issue