VTech VT 1962 manual Cid-Caller Id, Call Waiting Caller ID Type II CID, Word About Caller ID CID

Page 27

CID-CALLER ID

CID - Caller ID

Your VT 1962 cordless phone is capable of displaying the name and/ or phone number of the person calling, before you answer the phone. Subscription to Caller ID service through your local phone company is required to utilize this feature.

If you subscribe to alphanumeric (name

&number) Caller ID service, the calling party's name and phone number (when available) will be displayed on the LCD screen while the phone is ringing.

If you subscribe to numeric (number only) Caller ID service, the calling party's phone number (when available) will be displayed on the LCD screen while the phone is ringing.

Call Waiting Caller ID (TYPE II CID)

Your VT 1962 cordless phone is also capable of displaying Caller ID information in connection with a Call Waiting signal. If you are on a call, and receive a Call Waiting alert signal, the LCD will display the name and/or number (when available) of the party trying to reach you. As above, subscription to Call Waiting ID service through your local phone company is required in order to utilize this feature.

A Word About Caller ID - CID

Due to regional incompatibilities, Caller ID information may not be available for every call you receive. In addition, the calling party may intentionally block their name & phone number from being sent.

NOTE:

You must be in an area where CID service is available and you must subscribe to it to use this feature.

If you do not subscribe to the CID service, the phone will still operate normally except that the CID information is not received or displayed.

Receiving and Storing Calls

This unit receives and displays all CID information, the caller's telephone number, the callers name and the exact date and time of the call.

The phone sequentially numbers these call records and retains them in the unit's CID memory for later review. These call record number are displayed as the firsr two digits in the display. The unit can store up to 50 numbers in its memory.

Once the CID memory is full, any new call forces a deletion of the oldest call record.

Dialing From CID Memory

NOTE:

Only the last 7 digits of any number are displayed when dialing from CID memory.

For example, when you press and hold the 7 key to view the phone number, you would see the following:

27

Image 27
Contents Introduction MHz Operation Special FeaturesParts Check List FCC Part FCC and IC RegulationsThis telephone is registered for use in Canada IC Industry CanadaFCC and IC Regulations Read and understand all instructions Important Safety InstructionsIf the product exhibits a distinct change in performance Its Impossible To Over-Charge The Battery Pack Replacing the Battery PackCharging The Handset Battery Pack To Charge The Battery PackReplace the battery case cover by sliding the cover upwards Replacing a Drained Handset battery Spare Battery ChargerInstallation Power BackupRbrctm Seal The Rbrcr Seal on the nickel-cadmium battery Getting Started Setting Up Your VTAC Power Adapter Setting the Tone/Pulse SwitchConnect Telephone Line Cord Wall Mounting Using The Wall Mount AdapterLCD Display Messages LCD DisplayHandset Layout Handset FeaturesBase Unit Layout Base Unit FeaturesQuick Reference Guide To exit press OFF Using RedialMemory Dialing Speed Dialing CID Caller IDBasic Operation Temporary Tone Switching calls using FlashAdvanced Functions Call WaitingTo turn off the ringer do the following Changing Ringer TypesTurning Off The Ringer Checking The Ringer TypeAdvanced Dialing CLR/DEL Key FunctionPress Phone to get a line Memory DialingDialing From Memory If programming is unsuccessful the unit will displayChanging Stored Numbers Deleting Stored NumbersStoring Special Codes Receiving and Storing Calls CID-CALLER IDCall Waiting Caller ID Type II CID Word About Caller ID CIDSpecial Message Indicators Out of Area Calls Transmission ErrorPrivate Calls Reviewing CID Records Reviewing NumbersDeleting Numbers Set Outgoing Message OGM Answering System SetupDefault Answering System Settings Answering System Program- ming OverviewDay and Time Security code default setting isSet Announce Only Set Audible Message AlertSet Base Ringer On/Off Set Number of RingsBase ringer can be turned on or OFF Saving Messages Answering System OperationsLeaving a Message Incoming Message Listening to Messages / MemosTurning the Answering Machine Deleting MessagesChanging Playback Speed Changing Speaker VolumeCall Screening Check Current Day and TimeMemory Full Power Failure LED displays What it means Flashing numberYou have no new messages Playing Messages Remotely Remote Operation of Answering SystemMemo Recording Repeat Messages During PlaybackSkip Messages During Playback Stop Message PlaybackExiting Remote Operation Additional Operating Tips Headset Operation OperationBelt Clip Maintenance Phone Doesnt Work At All Handset Does Not Ring When You Receive a CallYou Hear Other Calls While Using Your Phone Case of DifficultyCommon Cure For Electronic Equipment At our option, repair or replace your unit Warranty StatementAny defect in material or workmanship To the original purchaser only ONE YearWhat does OUR Warranty not COVER? Technical Specifications Crystal Controlled Dual PLL SynthesizerHandset 295 grams Base 470 grams Table of Contents Issue