VTech VT 1962 manual Quick Reference Guide

Page 19

QUICK REFERENCE GUIDE

Set-Up

•Plug AC adapter into a standard electrical outlet and Base Unit

•Set Dial Mode switch to PULSE or TONE. The unit is factory set to TONE.

•Let the Handset battery pack charge for 16 hours before first use.

•Connect telephone line cord to Base Unit and telephone jack.

Making Calls

•Press the PHONE key. When the "PHONE ON" indicator is displayed and you hear a dial tone, dial the number.

OR

•Enter the number to be dialed on the LCD and then press the PHONE key.

To Mute A Call

•Press MUTE to disable the Handset microphone.

•Press MUTE again to return to normal two way conuersation.

To Page The Handset

•To page from the Base, press

PAGE .

•To cancel the PAGE either press PAGE again on the Base or press OFF on the Handset.

Storing Memory (SPEED) DIAL NUMBERS:

•The phone should be OFF.

•Enter the number you wish to store on the LCD up to a maximum of 20 digits.

Answering Calls

•To answer a call, press any key other than OFF , MUTE , or the Volume Keys. The Handset will NOT auto-answer when lifted off the Base cradle.

Hanging Up

•Press OFF or place the Handset in the cradle to hang up a call.

To Place A Call On Hold

•Press HOLD on the Handset to place an active call on hold. Press HOLD again to return to the call.

Storing

The Phone should be

OFF

Enter Phone number

Press

You will see

Enter Memory location (01-20)

•Press PROG . The LCD will

display "PROGRAM LOCATION "

•Enter a two digit memory location (01 .. 20), the unit will store the number, emit a happy tone to confirm successful programming and exit program mode.

19

Image 19

Contents Introduction MHz Operation Special FeaturesParts Check List FCC Part FCC and IC RegulationsThis telephone is registered for use in Canada IC Industry CanadaFCC and IC Regulations Read and understand all instructions Important Safety InstructionsIf the product exhibits a distinct change in performance Its Impossible To Over-Charge The Battery Pack Replacing the Battery PackCharging The Handset Battery Pack To Charge The Battery PackReplace the battery case cover by sliding the cover upwards Replacing a Drained Handset battery Spare Battery ChargerInstallation Power BackupRbrctm Seal The Rbrcr Seal on the nickel-cadmium battery Getting Started Setting Up Your VTAC Power Adapter Setting the Tone/Pulse SwitchConnect Telephone Line Cord Wall Mounting Using The Wall Mount AdapterLCD Display Messages LCD DisplayHandset Layout Handset FeaturesBase Unit Layout Base Unit FeaturesQuick Reference Guide To exit press OFF Using RedialMemory Dialing Speed Dialing CID Caller IDBasic Operation Temporary Tone Switching calls using FlashAdvanced Functions Call WaitingTo turn off the ringer do the following Changing Ringer TypesTurning Off The Ringer Checking The Ringer TypeAdvanced Dialing CLR/DEL Key FunctionPress Phone to get a line Memory DialingDialing From Memory If programming is unsuccessful the unit will displayDeleting Stored Numbers Changing Stored NumbersStoring Special Codes Receiving and Storing Calls CID-CALLER IDCall Waiting Caller ID Type II CID Word About Caller ID CIDTransmission Error Special Message Indicators Out of Area CallsPrivate Calls Reviewing CID Records Reviewing NumbersDeleting Numbers Set Outgoing Message OGM Answering System SetupDefault Answering System Settings Answering System Program- ming OverviewDay and Time Security code default setting isSet Announce Only Set Audible Message AlertSet Number of Rings Set Base Ringer On/OffBase ringer can be turned on or OFF Saving Messages Answering System OperationsLeaving a Message Incoming Message Listening to Messages / MemosTurning the Answering Machine Deleting MessagesChanging Playback Speed Changing Speaker VolumeCall Screening Check Current Day and TimeMemory Full Power Failure Flashing number LED displays What it meansYou have no new messages Playing Messages Remotely Remote Operation of Answering SystemMemo Recording Repeat Messages During PlaybackSkip Messages During Playback Stop Message PlaybackExiting Remote Operation Additional Operating Tips Operation Headset OperationBelt Clip Maintenance Phone Doesnt Work At All Handset Does Not Ring When You Receive a CallYou Hear Other Calls While Using Your Phone Case of DifficultyCommon Cure For Electronic Equipment At our option, repair or replace your unit Warranty StatementAny defect in material or workmanship To the original purchaser only ONE YearWhat does OUR Warranty not COVER? Crystal Controlled Dual PLL Synthesizer Technical SpecificationsHandset 295 grams Base 470 grams Table of Contents Issue