VTech VT 1962 manual If the product exhibits a distinct change in performance

Page 8

IMPORTANT SAFETY INSTRUCTIONS

12.Unplug this product from the wall outlet and refer servicing to a VTech authorized service facility under the following conditions:

A.When the power supply cord or plug is damaged or frayed.

B.If liquid has been spilled into the product.

C.If the product has been exposed to rain or water.

D.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, because improper adjustment of other controls may result in damage and will often require extensive work by a VTech authorized technician to restore the product to normal operation.

E.If the product has been dropped and the cabinet has been damaged.

F.If the product exhibits a distinct change in performance.

13.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lighting.

14.Do not use the telephone to report a gas leak in the vicinity of the leak.

VTECH COMMUNICATIONS SERVICE DEPT. at 1-800-595-9511. In Canada, call VTECH Electronics at 1-800-267-7377.

SAVE THESE INSTRUCTIONS

8

Image 8

Contents Introduction Special Features MHz OperationParts Check List FCC and IC Regulations FCC PartIC Industry Canada This telephone is registered for use in CanadaFCC and IC Regulations Important Safety Instructions Read and understand all instructionsIf the product exhibits a distinct change in performance Replacing the Battery Pack Charging The Handset Battery PackTo Charge The Battery Pack Its Impossible To Over-Charge The Battery PackReplace the battery case cover by sliding the cover upwards Spare Battery Charger InstallationPower Backup Replacing a Drained Handset batteryRbrctm Seal The Rbrcr Seal on the nickel-cadmium battery Setting Up Your VT AC Power AdapterSetting the Tone/Pulse Switch Getting StartedConnect Telephone Line Cord Using The Wall Mount Adapter Wall MountingLCD Display LCD Display MessagesHandset Features Handset LayoutBase Unit Features Base Unit LayoutQuick Reference Guide Using Redial Memory Dialing Speed DialingCID Caller ID To exit press OFFBasic Operation Switching calls using Flash Advanced FunctionsCall Waiting Temporary ToneChanging Ringer Types Turning Off The RingerChecking The Ringer Type To turn off the ringer do the followingCLR/DEL Key Function Advanced DialingMemory Dialing Dialing From MemoryIf programming is unsuccessful the unit will display Press Phone to get a lineStoring Special Codes Changing Stored NumbersDeleting Stored Numbers CID-CALLER ID Call Waiting Caller ID Type II CIDWord About Caller ID CID Receiving and Storing CallsPrivate Calls Special Message Indicators Out of Area CallsTransmission Error Reviewing Numbers Reviewing CID RecordsDeleting Numbers Answering System Setup Default Answering System SettingsAnswering System Program- ming Overview Set Outgoing Message OGMSecurity code default setting is Day and TimeSet Audible Message Alert Set Announce OnlyBase ringer can be turned on or OFF Set Base Ringer On/OffSet Number of Rings Answering System Operations Leaving a Message Incoming MessageListening to Messages / Memos Saving MessagesDeleting Messages Turning the Answering MachineChanging Speaker Volume Call ScreeningCheck Current Day and Time Changing Playback SpeedMemory Full Power Failure You have no new messages LED displays What it meansFlashing number Remote Operation of Answering System Playing Messages RemotelyRepeat Messages During Playback Skip Messages During PlaybackStop Message Playback Memo RecordingExiting Remote Operation Additional Operating Tips Belt Clip Headset OperationOperation Maintenance Handset Does Not Ring When You Receive a Call You Hear Other Calls While Using Your PhoneCase of Difficulty Phone Doesnt Work At AllCommon Cure For Electronic Equipment Warranty Statement Any defect in material or workmanshipTo the original purchaser only ONE Year At our option, repair or replace your unitWhat does OUR Warranty not COVER? Handset 295 grams Base 470 grams Technical SpecificationsCrystal Controlled Dual PLL Synthesizer Table of Contents Issue