Cisco Systems MD-110 manual To enter port settings, To enable extensions beginning with zero

Page 18

Chapter 1 Ericsson MD-110 Serial Integration

Configuring Cisco Unity for the Integration

To enter port settings

Step 1 In the Cisco Unity Administrator, go to System > Ports.

Step 2 Select a port in the table.

Step 3 Indicate the settings for the port.

For a hunt group, use the first voice-messaging ports for incoming calls and the last ports to dial out. This helps minimize the possibility of a collision, in which an incoming call arrives on a port at the same time that Cisco Unity takes the port off-hook to dial out.

Step 4 Type the extension for the port.

Step 5 Repeat Steps 2 through 4 for the remaining ports.

Step 6 Click the Save icon.

Step 7 For the settings to take effect, exit the Cisco Unity software. For more information, see the appendix, “Exiting and Starting the Cisco Unity Software and Server.”

If your phone system uses extension numbers that begin with zero (for example, 0123 or 09876), perform the following procedure.

Note that after the procedure is performed all extension numbers must have the same number of digits. In this case, for example, 0123 and 1234 are both allowed, but 0123 and 234 are not allowed.

To enable extensions beginning with zero

Step 1 On the Cisco Unity server, navigate to the \CommServer\Intlib directory on the drive you installed Cisco Unity.

Step 2 In the Intlib directory, locate the file Ericsson0001.ini.

Step 3 Open the file in a text editor.

Step 4 In the Configuration section of the file, locate the following line:

AllowZeroLeadingExtensions=0

Step 5 Change the final digit to 1, so the line reads:

AllowZeroLeadingExtensions=1

	Ericsson MD-110 Serial Integration Guide
1-6	OL-1290-01

Image 18

Contents

Ericsson MD-110 Serial Integration Guide Ericsson MD-110 Serial Integration Guide Dual Phone System Integration Shutting Down or Restarting the Cisco Unity Server A-2 Purpose AudienceOrganization ConventionsConvention Description Cisco Unity Documentation Document LocationObtaining Documentation World Wide WebDocumentation CD-ROM Ordering DocumentationDocumentation Feedback Cisco.com To access Cisco.com, go to the following websiteObtaining Technical Assistance Technical Assistance CenterContacting TAC by Using the Cisco TAC Website Xii Integration Overview Integration StepsRequirements Phone SystemCisco Unity Server Integration Description Connections Between the Phone System and Cisco UnityIntegration Features Go to System Licensing Licensed Features Configuring Cisco Unity for the IntegrationTo confirm that the integration is enabled Switch Parameter Required SettingTo enter port settings To enable extensions beginning with zeroChange the final digit to 1, so the line reads Programming the Phone System To program the phone systemIs restarted Transfer type UsageTesting the Integration To set up the test configurationNotification MonitorTo test an external call with release transfer To set up supervised transfer on Cisco Unity To test an internal call with release transferTransfer To return Example Subscriber to the default settings Set the Rings to Wait For field to Click the Save iconTo test supervised transfer Ericsson MD-110 Serial Integration Testing the Integration OL-1290-01 Integration Steps When No Phone Systems Are Installed Dual Phone System Integration OverviewEricsson MD-110 Serial Integration Guide Changing Cisco Unity Administrator Settings To specify switch settings for the traditional phone system To modify voice port settings To specify switch settings for Cisco CallManagerGo to System Switch IP Switch To reach someone on the traditional phone systemEricsson MD-110 Serial Integration Guide OL-1290-01 Changing the Number of Installed Ports Stop Unity To reinstall the AV-Cisco Tapi service providerTo remove the existing AV-Cisco TSP ProgramsRestart the Cisco Unity server Exiting the Cisco Unity Software To exit the Cisco Unity software from another computerTo shut down or restart the Cisco Unity server Starting the Cisco Unity SoftwareClick Shut Down Click Shut Down or RestartClick Start Cisco Unity To start the Cisco Unity software from another computerOL-1290-01 Phone System Integration To set the Port assignments in the Registry