Cardo G4 MP3 Music Wireless Option A2DP, A2DP and Avrcp profiles mostly 3rd generation devices

Page 10

NOTE: The priority schedule of your headset has been set in a way to avoid incoming intercom calls to interrupt GPS instructions in progress. In such case the intercom caller will hear a busy signal and you will hear two beeps, indicating that an intercom caller is trying to page you. (see section 4.3 for details on audio priorities of paired devices).

6.3 MP3 MUSIC (WIRELESS OPTION – A2DP)

Your headset is designed to receive wireless stereo music from A2DP sources and mobile phones that support the Bluetooth

A2DP and AVRCP profiles (mostly 3rd generation devices).

Using a Bluetooth device that supports the AVRCP profile will allow you to operate all major A2DP source functions directly from your headset.

NOTE: The G4 can also receive audio via the enclosed cable from non- Bluetooth MP3 Players or audio sources as described in section 7.2

While listening to music from an A2DP source, you will not miss any mobile or intercom calls, as the headset will automatically stop the music giving preference to the incoming call. However, after you ter- minate your call, some MP3 sources may not automatically continue but require manual re-activation.

SETTING UP YOUR MP3 PLAYER FOR BLUETOOTH STEREO A2DP TRANSMISSION

To use a Bluetooth Stereo (A2DP) enabled MP3 Player or Adapter to listen to stereo music, you must first pair the device to your headset.

PAIRING THE HEADSET TO AN MP3 PLAYER OR ADAPTER

NOTE: If your A2DP source is integrated inside your Mobile Phone, then you should pair it with your headset as described in section 6.1 above

1.Turn on your MP3 Player or Adapter, and make sure that its Blue- tooth function is activated.

2.With the scala rider G4 headset turned ON, press and hold the Mobile Button for at least six seconds until the Red and Blue Lights begin alternating rapidlyץ

3.Search for Bluetooth headsets on your MP3 Player by following the device’s instructions.

NOTE: For use of a Bluetooth adapter, follow the device’s instructions

4.After a few seconds the MP3 Player will list “scala rider G4” as a discovered device. Select it and follow your MP3 Player’s instruc- tions to accept the pairing.

5.If your MP3 player prompts for a PIN or Passkey enter 0000 (four zeros).

6.Once pairing is complete, your MP3 Player or Adapter may confirm that pairing has succeeded, and the headset will begin flashing slowly in Blue.

NOTE: If the Pairing process is not completed within two minutes the headset will return to Standby mode.

Operating your A2DP source from your headset

Play

press and hold the MP3 Button for 3 seconds

 

 

Pause/Stop*

press and hold the MP3 Button for 3 seconds

 

 

Forward

Press and hold the Volume Up Button for 3 seconds

 

 

Rewind

Press and hold the Volume Down Button for 3 seconds

 

 

* Varies depending on your mobile phone model

10 scala rider® G4™ PowerSet

Page 9 Page 11
Image 10
Page 9 Page 11
Contents User Guide Table of Contents Introduction Additional Special FeaturesAs a stereo headset for listening to the built-in FM Radio Contents of the Retail BOX Charging the HeadsetGeneral Functions Basic Setup and ConfigurationDisable/Enable status announcements Press and hold Spoken Status AnnouncementsGetting Started Firmware Upgrade OptionResetting Your Headset Mounting the Headset on the HelmetPositioning the Microphone and Speakers Using the FLIP-UP Antenna Attaching and Removing the Headset from Helmet ClampMobile Phone Pairing the Headset to a Bluetooth Mobile PhonePairing the Headset to a GPS Device GPS DeviceA2DP and Avrcp profiles mostly 3rd generation devices MP3 Music Wireless Option A2DPPairing the Headset to AN MP3 Player or Adapter Operating your A2DP source from your headsetFM Radio Searching for and setting new stationsSaving a selected station Using the Mobile Phone Initiating and Receiving Mobile Phone CallsIntroduction Using the IntercomStatus Lights Backwards CompatibilityInitiate Intercom Calls Select your preferred Pairing OptionReceiving Intercom Calls Reset Pairing Restoring the Original Default Configuration ENABLE/DISABLE Voice Connect Feature VOXTroubleshooting the Intercom Set-up and configuration three-way intercom connectivity Initiate Intercom callsPairing Four Scala Rider G4 Headsets 10c. FOUR-WAY IntercomStep Two Pair Driver 3 to Passenger 4 via Channel a Both headsets should now be flashing slowly in BlueUsing the G4 for Intercom with Other SCALA RIDER Headsets Step Three Pair Passenger 2 to Passenger 4 via Channel BInitiate Intercom calls from scala rider G4 11a. TWO-WAY Intercom with scala rider Q211b. TWO-WAY Intercom with earlier scala rider models Using your scala rider G4 with two scala rider Q2 headsets Initiate Intercom calls from earlier scala rider headsets11c. Three WAY Intercom with other scala rider headsets Initiate Intercom calls from scala rider Q2Or contact us at support@cardosystems.com SupportFor additional information please visit our website at Phone USA and Canada + International +4989 450European CE Notice  Operation is subject to the following two conditionsIC RF Radiation Exposure Statement Declaration of Conformity DOCDisclaimer of Warranty Limitation of Liability
Top Page Image Contents