Cardo G4 manual Positioning the Microphone and Speakers

Page 7

3. Adjust the Helmet Clamp’s location on the Helmet so that the

microphone is located opposite the center of

your mouth. You may need to reposition the

Clamp repeatedly until you identify the best

b. Attach the microphone to the Velcro, as shown in photo. c. When done, tighten the screws of the clamp

5.3 POSITIONING THE MICROPHONE AND SPEAKERS

English

spot. (Be sure to clean the selected area prior

to the gluing process).

4. Use the pre-moistened Towlette to clean the helmet area where

you want to install the Glue Plate. Allow to dry thoroughly.

5. Peel the foil cover from the Glue Plates’ adhesive pad.

6. Place the Glue Plate into position according to #3. Press firmly

15 seconds on all 3 parts of the Glue Plate.

7. The adhesive pad bonds to full strength over the next 24

hours. Therefore it is recommended to not use the headset

during this 24 hour period.

8. Fasten the Clamp to the Glue Plate using the Allen screws that

were previously removed.

If you have purchased a helmet clamp version with the corded microphone, please proceed as follows:

5.2ATTACHING THE CORDED MICROPHONE CLAMP ON A

 FULL-FACED HELMET

If you are using the corded microphone version, you must first make sure your helmet clamp is attached to your

The microphone must be positioned in front of the center of your mouth as detailed above.

Attach the speakers to the Velcro inside your helmet, opposite your ears (short speaker cord for left ear & long speaker cord for right ear). Use the supplied Velcro pads if needed.

Using two speakers inside the helmet may be prohibited in certain jurisdictions. If this is the case, you should tuck away the long corded speaker underneath the helmet padding as follows:

Lead the speaker cord [B] alongside the rim of the padding to the right side and then back to the left side, near speaker [A]. Then place the speaker [B] underneath the padding.

Speaker A

Speaker B

Cable

Speaker B

Speaker B

Speaker A

helmet as described in previous section (5.1). Clean the exact spot on the internal padding of the helmet, opposite your mouth, where the microphone will be placed.

a. Peel the foil cover from the adhesive Velcro pad and place the Velcro pad on the chosen location opposite your mouth.

NOTE: For best audio results, make sure that both of your speakers actually touch your ears.

Please visit us at www.cardosystems.com/faq and look for some very useful tips under the Audiokit category.

scala rider® G4™ PowerSet

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents User Guide Table of Contents Introduction Additional Special FeaturesAs a stereo headset for listening to the built-in FM Radio Charging the Headset Contents of the Retail BOXSpoken Status Announcements Basic Setup and ConfigurationDisable/Enable status announcements Press and hold General FunctionsMounting the Headset on the Helmet Firmware Upgrade OptionResetting Your Headset Getting StartedPositioning the Microphone and Speakers Attaching and Removing the Headset from Helmet Clamp Using the FLIP-UP AntennaGPS Device Pairing the Headset to a Bluetooth Mobile PhonePairing the Headset to a GPS Device Mobile PhoneOperating your A2DP source from your headset MP3 Music Wireless Option A2DPPairing the Headset to AN MP3 Player or Adapter A2DP and Avrcp profiles mostly 3rd generation devicesFM Radio Searching for and setting new stationsSaving a selected station Initiating and Receiving Mobile Phone Calls Using the Mobile PhoneBackwards Compatibility Using the IntercomStatus Lights IntroductionInitiate Intercom Calls Select your preferred Pairing OptionReceiving Intercom Calls Reset Pairing Restoring the Original Default Configuration ENABLE/DISABLE Voice Connect Feature VOXTroubleshooting the Intercom Initiate Intercom calls Set-up and configuration three-way intercom connectivity10c. FOUR-WAY Intercom Pairing Four Scala Rider G4 HeadsetsStep Three Pair Passenger 2 to Passenger 4 via Channel B Both headsets should now be flashing slowly in BlueUsing the G4 for Intercom with Other SCALA RIDER Headsets Step Two Pair Driver 3 to Passenger 4 via Channel aInitiate Intercom calls from scala rider G4 11a. TWO-WAY Intercom with scala rider Q211b. TWO-WAY Intercom with earlier scala rider models Initiate Intercom calls from scala rider Q2 Initiate Intercom calls from earlier scala rider headsets11c. Three WAY Intercom with other scala rider headsets Using your scala rider G4 with two scala rider Q2 headsetsPhone USA and Canada + International +4989 450 SupportFor additional information please visit our website at Or contact us at support@cardosystems.comDeclaration of Conformity DOC Operation is subject to the following two conditionsIC RF Radiation Exposure Statement European CE Notice Limitation of Liability Disclaimer of Warranty
Top Page Image Contents