Cardo G4 manual Getting Started, Firmware Upgrade Option, Resetting Your Headset

Page 6

4.4 FIRMWARE UPGRADE OPTION

In the future you will be able to install firmware upgrades and program patches to keep the software of your G4 up-to-date. Among others, future firmware upgrades will include additional

status announcements and other valuable functions. To ensure that you don’t miss out on the latest versions, please register online at www. cardosystems.com/download/softwareupgrade and have your serial number ready. For downloading upgrades, please use the USB cable included in the retail package of your scala rider G4.

Please note that until further notice, upgrades will only be available for Windows™ based computers with XP™ or Vista™ operating systems.

4.5 RESETTING YOUR HEADSET

If your headset fails to respond despite repeated attempts, you can reset your headset by charging it. After approximately 10 seconds, remove the headset from the charger and turn it on again. Your head- set should now respond as expected.

5. GETTING STARTED

5.1  MOUNTING THE HEADSET ON THE HELMET

The Helmet clamp that includes your microphone and speakers must first be mounted on the helmet. Once mounted, the headset unit can be attached or detached from the clamp at any time (sec. 5.4).

There are two methods that can be used to attach the clamp to the helmet:

Standard Method: Recommended for most helmet types.

Glue Plate Method: Recommended for helmets to which the standard method cannot be applied, using the Glue Plate included in the box.

Glue Plate

Standard Method: Fastening the Clamp to the

Helmet

1.Use the enclosed Allen Wrench to loosen the two screws on the Back Plate.

2.Slide the Back Plate between the internal padding and the external shell of the helmet.

3.Adjust the clamp’s location so that the microphone is located in front of the center of your mouth, and then tighten the screws. You may need to reposition the Clamp repeatedly until you identify the best spot.

If you have purchased a helmet clamp version with the corded microphone, please refer to section 5.2.

Glue Plate Method: Attaching the Clamp by way of glue

You have the option to glue the Helmet Clamp onto your helmet, when the above standard method cannot be used, or in case you prefer to secure the Helmet Clamp with adhesive glue.

Caution: This process can be done only once!

NOTE: While we have no reason to believe that the gluing option might nega- tively affect any helmet, Cardo does not assume any responsibility to that effect, irrespective of its nature and circumstances. The Glue Plate is offered as a free option that you may choose to use at your own risk and subject to renouncement of any future claims.

1.Use the enclosed Allen Wrench to remove both Allen screws and release the Helmet Clamp’s back plate.

2.Determine the location on the helmet where the Helmet Clamp must be attached.

6 scala rider® G4™ PowerSet

Page 5 Page 7
Image 6
Page 5 Page 7
Contents User Guide Table of Contents Additional Special Features IntroductionAs a stereo headset for listening to the built-in FM Radio Contents of the Retail BOX Charging the HeadsetGeneral Functions Basic Setup and ConfigurationDisable/Enable status announcements Press and hold Spoken Status AnnouncementsGetting Started Firmware Upgrade OptionResetting Your Headset Mounting the Headset on the HelmetPositioning the Microphone and Speakers Using the FLIP-UP Antenna Attaching and Removing the Headset from Helmet ClampMobile Phone Pairing the Headset to a Bluetooth Mobile PhonePairing the Headset to a GPS Device GPS DeviceA2DP and Avrcp profiles mostly 3rd generation devices MP3 Music Wireless Option A2DPPairing the Headset to AN MP3 Player or Adapter Operating your A2DP source from your headsetSearching for and setting new stations FM RadioSaving a selected station Using the Mobile Phone Initiating and Receiving Mobile Phone CallsIntroduction Using the IntercomStatus Lights Backwards CompatibilitySelect your preferred Pairing Option Initiate Intercom CallsReceiving Intercom Calls ENABLE/DISABLE Voice Connect Feature VOX Reset Pairing Restoring the Original Default ConfigurationTroubleshooting the Intercom Set-up and configuration three-way intercom connectivity Initiate Intercom callsPairing Four Scala Rider G4 Headsets 10c. FOUR-WAY IntercomStep Two Pair Driver 3 to Passenger 4 via Channel a Both headsets should now be flashing slowly in BlueUsing the G4 for Intercom with Other SCALA RIDER Headsets Step Three Pair Passenger 2 to Passenger 4 via Channel B11a. TWO-WAY Intercom with scala rider Q2 Initiate Intercom calls from scala rider G411b. TWO-WAY Intercom with earlier scala rider models Using your scala rider G4 with two scala rider Q2 headsets Initiate Intercom calls from earlier scala rider headsets11c. Three WAY Intercom with other scala rider headsets Initiate Intercom calls from scala rider Q2Or contact us at support@cardosystems.com SupportFor additional information please visit our website at Phone USA and Canada + International +4989 450European CE Notice  Operation is subject to the following two conditionsIC RF Radiation Exposure Statement Declaration of Conformity DOCDisclaimer of Warranty Limitation of Liability
Top Page Image Contents