Cardo G4 manual Both headsets should now be flashing slowly in Blue, Making 4-Way Intercom calls

Page 18

NOTE: The scala rider G4 PowerSet package, contains two factory paired G4 headsets. If you did not change the original pairing settings, you can skip “step one” below:

Step One: Pair Driver 1 to Passenger 2 via Channel “A” as follows

a. Turn both headsets ON by pressing and holding the Mobile Buttons until the Blue Light flashes three times.

b. Both headsets should now be flashing slowly in Blue.

c. Press and hold CHANNEL (“A”) BUTTON on both headsets for at least six seconds until the headset’s BLUE or RED Light begins flashing rapidly, indicating that they have entered the Intercom Pairing mode. (See Intercom Channel Table for Pairing Light indication for each CHANNEL)

d. Release the buttons and wait until both headsets display a solid light for two seconds, indicating that the two headsets are now paired for Intercom connections. (This may take up to two minutes)

Step Two: Pair Driver 3 to Passenger 4 via Channel “A”

Repeat the above pairing procedure between Driver 3 and Passenger 4

Step Three: Pair Passenger 2 to Passenger 4 via Channel “B”

Repeat the above pairing procedure between Passenger 2 and Pas- senger 4 using the Channel “B” button. (instead of Channel “A” button as described in bullet c above).

Your 4-Way Conference Intercom Pairing is now complete and ready to use.

NOTE: If the Pairing process is not completed within two minutes the headsets will return to Standby mode.

Making 4-Way Intercom calls

Once you have successfully paired the four headsets as described above, and all units are in standby mode, proceed as follows to start a

4-way Conference Intercom call:

a. Passenger 2 should press Button “B” to initiate a call with Passenger 4. Wait until audio is heard on both headsets and proceed to the next step.

b. Driver 1 should press Button “A” to initiate a call with Passenger 2.

c. Driver 3 should press Button “A” to initiate a call with Passenger 4.

Now the 4-way intercom conference mode is established.

NOTE: If one of the headsets should disconnect or drop off from the 4-way call and fails to reconnect, repeat the three steps above.

9.11USING THE G4 FOR INTERCOM WITH OTHER   SCALA RIDER HEADSETS

INTERCOM

PAIRING / CONNECTION

PAIRING MODE LED

CHANNEL

BUTTON

INDICATORS

 

 

 

CHANNEL “A”

CHANNEL “A” BUTTON

Rapid RED flashing

 

 

 

CHANNEL “B”

CHANNEL “B” BUTTON

Rapid BLUE flashing

 

 

 

18 scala rider® G4™ PowerSet

Page 17 Page 19
Image 18
Page 17 Page 19
Contents User Guide Table of Contents Additional Special Features IntroductionAs a stereo headset for listening to the built-in FM Radio Contents of the Retail BOX Charging the HeadsetGeneral Functions Basic Setup and ConfigurationDisable/Enable status announcements Press and hold Spoken Status AnnouncementsGetting Started Firmware Upgrade OptionResetting Your Headset Mounting the Headset on the HelmetPositioning the Microphone and Speakers Using the FLIP-UP Antenna Attaching and Removing the Headset from Helmet ClampMobile Phone Pairing the Headset to a Bluetooth Mobile PhonePairing the Headset to a GPS Device GPS DeviceA2DP and Avrcp profiles mostly 3rd generation devices MP3 Music Wireless Option A2DPPairing the Headset to AN MP3 Player or Adapter Operating your A2DP source from your headsetSearching for and setting new stations FM RadioSaving a selected station Using the Mobile Phone Initiating and Receiving Mobile Phone CallsIntroduction Using the IntercomStatus Lights Backwards CompatibilitySelect your preferred Pairing Option Initiate Intercom CallsReceiving Intercom Calls ENABLE/DISABLE Voice Connect Feature VOX Reset Pairing Restoring the Original Default ConfigurationTroubleshooting the Intercom Set-up and configuration three-way intercom connectivity Initiate Intercom callsPairing Four Scala Rider G4 Headsets 10c. FOUR-WAY IntercomStep Two Pair Driver 3 to Passenger 4 via Channel a Both headsets should now be flashing slowly in BlueUsing the G4 for Intercom with Other SCALA RIDER Headsets Step Three Pair Passenger 2 to Passenger 4 via Channel B11a. TWO-WAY Intercom with scala rider Q2 Initiate Intercom calls from scala rider G411b. TWO-WAY Intercom with earlier scala rider models Using your scala rider G4 with two scala rider Q2 headsets Initiate Intercom calls from earlier scala rider headsets11c. Three WAY Intercom with other scala rider headsets Initiate Intercom calls from scala rider Q2Or contact us at support@cardosystems.com SupportFor additional information please visit our website at Phone USA and Canada + International +4989 450European CE Notice  Operation is subject to the following two conditionsIC RF Radiation Exposure Statement Declaration of Conformity DOCDisclaimer of Warranty Limitation of Liability
Top Page Image Contents