Cardo G4 manual Contents of the Retail BOX, Charging the Headset

Page 4

2. CONTENTS OF THE RETAIL BOX

2 Helmet clamps (subject to the version purchased: Boom-Mounted or Cord-Mounted Microphone)

Two speakers

MP3 Jack

Noise(back of clamp) canceling

microphone

Sliding Panel

Flexible Boom

2 scala rider G4 headsets

Volume Up /		Flip-up
Volume Up /		antenna
Forward	Mobile Volume
Button	Mobile Volume
	Phone	Down /
	Button	Rewind

Button

		Silicone cover
Channel A		Charging Jack
Button		& Firmware
• Connect to		& Firmware
• Connect to		download port
Rider A	LED	Channel B Button
• MP3 Button		• Connect to Rider B
		• Connect to Rider B
		• FM Radio Button

2 Wall charger plugs

2 USB adapter cables

2 Allen wrenches

4 Velcro pads

2 MP3 cables

2 Glue plates

2Pre-moistened towlettes

2Carry pouches

4 Microphone sponges

Flat sponges for full-face helmets and round sponges for other helmet types

User Guide, stickers, Warranty and Registration form

The scala rider G4 is also available in a cord-mounted microphone version to better fit certain full-faced helmets with tight chin sections

IMPORTANT:

Your headsets are water-resistant, designed for use under moderate rain or snow conditions. The cover lid protecting the Charging Jack should be kept tightly closed at all times to prevent moisture from entering the device.

NOTE: WHILE MOST INSTRUCTIONS ON THIS MANUAL REFER TO THE HEADSET IN SINGULAR, THEY APPLY TO BOTH UNITS UNLESS INDICATED OTHERWISE

3. CHARGING THE HEADSET

Make sure that your headset is fully charged for at least four hours before initial use. Open the silicone cover protecting the Charging jack and Firmware download port.

Insert the USB cable to the wall charger and insert the other end of the cable to the headset’s Charging Jack. While charging, the Red Light turns on. When charging is complete, the Red Light will turn off.

4 scala rider® G4™ PowerSet

Image 4

Contents User Guide Table of Contents Introduction Additional Special FeaturesAs a stereo headset for listening to the built-in FM Radio Contents of the Retail BOX Charging the HeadsetBasic Setup and Configuration Disable/Enable status announcements Press and holdGeneral Functions Spoken Status AnnouncementsFirmware Upgrade Option Resetting Your HeadsetGetting Started Mounting the Headset on the HelmetPositioning the Microphone and Speakers Using the FLIP-UP Antenna Attaching and Removing the Headset from Helmet ClampPairing the Headset to a Bluetooth Mobile Phone Pairing the Headset to a GPS DeviceMobile Phone GPS DeviceMP3 Music Wireless Option A2DP Pairing the Headset to AN MP3 Player or AdapterA2DP and Avrcp profiles mostly 3rd generation devices Operating your A2DP source from your headsetFM Radio Searching for and setting new stationsSaving a selected station Using the Mobile Phone Initiating and Receiving Mobile Phone CallsUsing the Intercom Status LightsIntroduction Backwards CompatibilityInitiate Intercom Calls Select your preferred Pairing OptionReceiving Intercom Calls Reset Pairing Restoring the Original Default Configuration ENABLE/DISABLE Voice Connect Feature VOXTroubleshooting the Intercom Set-up and configuration three-way intercom connectivity Initiate Intercom callsPairing Four Scala Rider G4 Headsets 10c. FOUR-WAY IntercomBoth headsets should now be flashing slowly in Blue Using the G4 for Intercom with Other SCALA RIDER HeadsetsStep Two Pair Driver 3 to Passenger 4 via Channel a Step Three Pair Passenger 2 to Passenger 4 via Channel BInitiate Intercom calls from scala rider G4 11a. TWO-WAY Intercom with scala rider Q211b. TWO-WAY Intercom with earlier scala rider models Initiate Intercom calls from earlier scala rider headsets 11c. Three WAY Intercom with other scala rider headsetsUsing your scala rider G4 with two scala rider Q2 headsets Initiate Intercom calls from scala rider Q2Support For additional information please visit our website atOr contact us at support@cardosystems.com Phone USA and Canada + International +4989 450Operation is subject to the following two conditions IC RF Radiation Exposure StatementEuropean CE Notice  Declaration of Conformity DOCDisclaimer of Warranty Limitation of Liability