BT 3200 SMS manual Battery low warning, Use it

Page 14

Synergy 3200 SMS user guide ~ 4th Edition ~ 16th October ’02 ~ 4678

Place the handset on the base. The red charging light will come on. The handset comes pre-registered to the base station as SYNERGY 1. This is shown on the display. The icon is also shown on the display and the battery icon.

Once the handset is fully charged, the display shows a full battery symbol.

BATTERY LEVELS

WEAK HALF-FULL FULL

Battery low warning

UP

If the handset battery symbol is empty

SETTING

and flashing, and you hear a warning

 

 

beep every 10 seconds, you will need

 

to recharge your handset before you can

 

use it.

 

 

 

Note

The

 

symbol on your handset display

 

indicates when you are in range of the base station. If the symbol flashes and you hear a warning beep, you

are out of range and will need to move closer to the base station.

The handset has a range of 300 metres outdoors and up to 50 metres indoors. The stated range of this product is measured in open field conditions. Walls, ceilings and metal structures will reduce the maximum range.

Battery performance

Under no circumstances should non-rechargeable batteries be used. Only use the approved batteries, type: rechargeable Nickel Metal Hydride (NiMH); Size AAA; Capacity 550 mAh; 1.2V. Using unapproved batteries will invalidate your guarantee and may damage the telephone.

To keep your batteries in the best condition, leave the handset off the base station for a few hours at a time (after the initial 16 hour charge).

Fully discharging the batteries at least once a week will help them last as long as possible.

However, charge capacity of rechargeable batteries will reduce with time as they wear out, so reducing talk/standby time of the handset. Eventually they will need to be replaced. New batteries can be obtained from the BT Synergy Helpline on 08706 058 047.

After charging your handset for the first time, subsequent charging time for the battery is approximately 6-8 hours a day. Batteries and handset may be come warm during charging. This is normal.

Under ideal condition the handset batteries should give about 14 hours talk time or 350 hours standby on a single charge. (This does not mean you can unplug the base station or leave it for this length of time without charge.)

Please note however, that new NiMH batteries do not reach full capacity until they have been in normal use for several days.

12

Page 13 Page 15
Image 14
Page 13 Page 15
Contents BT Synergy 3200 SMS Page At a glance HandsetBase 29 Jun 1025Quick Guide Information for the handset settings Menu Structure DD/MM HH/MM Menu Structure Using the telephone This guideIntroduction DectOne telephone line cord One belt clip Unpacking your Synergy 3200 SMSFor your records General Safety informationCleaning EnvironmentalInstall the batteries Setting upConnect the power supply to the base Battery low warning Use itConnect the telephone line cord to the base station Fit the belt clip onto the back of the handset if requiredUsing the telephone Making and receiving callsYou reach Handset Menu HandsfreeRedial Reach Ed. Phonebook SecrecyName and number Phonebook Add EntryTo dial a number from Phonebook To enter a pause in a stored numberHold the UP button until a PhonebookReach Edit Entry To edit Phonebook names and numbersReach Ed. Phonebook To delete a Phonebook name and numberBabycall Paging handsetsBaby call Off Room monitor modeMonitor mode Handset settings Time and dateSelect On To Keypad Lock and press button Press the UP button to selectOut of Range Key Press, Low Battery orTo Handset Menu and press Scroll to Handset Name To name a handsetUse the Down button to scroll Name already setBase settings To adjust the base ringer volumeScroll to PIN Code and press Scroll to Setup and pressUse the Down button to Show NEW Code?Display will flash Base 1 Scroll to Default and pressDefault settings are Earpiece volume Then SynergyCaller information not available Caller Display and Call WaitingCaller Display 0800 800Calls list To delete When the number you wantCall Waiting To delete is displayed, pressAt the handset To register a handset to the baseAt the base Press the UP or Down buttonHandset Handset is registeredTo de-register a handset from the base Shows Confirm?To see the base station identity Setting 0000 and pressTo register a handset to a different make of base station NumberTo make an internal call to another handset Internal callsTransferring calls Until Internal Call isCaller Three-way conversationDuring a call with an external Press the buttonSelect On or Off To switch ring priority setting on/offRing Priority and press Help Replacing the handset batteriesTelephone problems Possible cause Solution No display appearsTelephone problems Possible cause SolutionGuarantee General informationTechnical information Switchboard compatibilitySwitchboard external line access code RecallTo Pabx To SetupTo Pabx Setup Display shows PIN Code?Index REN Ringer Equivalence Number TTE Offices worldwide
Top Page Image Contents