SkyLink ML-001 Trouble Shooting Installation, Sensors, Programming Passwords, Changing Passwords

Page 11
Master Password

TROUBLE SHOOTING

INSTALLATION

Sensors

When a sensor is triggered, the control panel doesn’t respond at all, what is the problem?

My motion sensor sometimes gets triggered by itself, how can I prevent that?

After mounting the door sensor, it doesn’t work anymore.

-Make sure the battery in the sensor is installed properly, pay attention to the polarity.

-Make sure the sensor is learned to the control panel. Follow instructions on page 37 on how to learn a sensor.

-You may try to bring the sensor closer to the control panel, ensure it is not out of the operation range.

Ensure the motion sensor is not facing direct sunlight, nor any A/C or furnace vents. You may also reduce the sensitivity to low. If your motion sensor is located outdoors, you may want to relocate it.

- Please ensure the magnet is aligned with

the red marking on the transmitter.

- If you are mounting the sensor on to a

metal door or window, a spacer may be

required to avoid magnetic interference

caused by the metal door / window.

- Make sure the sensor is within the operation

range of the control panel by bringing it

Programming Passwords

can be used for programming, arming, disarming the system, and telephone access. The default Master Password is [1234].

Secondary Password can be used for arming, disarming the system, and telephone access. Secondary Password cannot be used for programming. The default Secondary Password is [0000].

Duress Password is used when you are forcibly compelled to disarm the control panel. Entering the duress password will stop the siren from sounding but the control panel will silently call the emergency phone numbers for help. The default Duress Password is [3838]. You should definitely change this password and let all the users know this password.

Changing Passwords

It is strongly recommended to change all 3 passwords when you first set up the system.

In order to change the password, follow the procedures below.

My motion sensor is not very responsive, sometimes when I walk by it, the control panel doesn’t respond, but sometimes it does.

closer to the control panel.

The motion sensor is designed to detect the “First Motion”. First Motion means no motion is detected within the past 20 seconds, and if a motion is then detected, that is the “First Motion”. So if you continue to walk in front of the motion sensor, it will only pick up the first motion. Unless you wait for 20 seconds, then walk again, the control panel will respond. Otherwise, the control will only respond to the first motion.

Step

Keys

Function

1

[PROG]

Enter

 

[MPIN]

Programming

 

mode

2

[2]

Select

 

 

password

 

 

programming

3

[1] or

Select which

 

[2] or

password to

 

[3]

change

Description

Note

Enter master

3 beeps for valid

password to

password. 1 long

programming mode

beep for invalid

 

password.

[1]- Master password

[2]- Secondary password

[3]- Duress password

4

[new

Enter new

 

4-digit

password

 

password]

 

5

[new

Enter new

 

4-digit

password to

 

password]

confirm

Select any 4-digit pass- word, each digit can be from 0 to 9

Enter the new password again for confirmation

3beeps if new pass- word is accepted. You will hear [Password Accepted]

–48–

–9–

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Email support@skylinkhome.com Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Tel 905Fax 905 Home Smart Center Important Safety Instructions EMC Declaration of ConformityDisarming a triggered control panel ContentSystem Configuration OperationFCC Information Consumer Information IntroductionOverview System Configuration Emergency Dialer AD-433S AccessoriesControl Module SW-100 Control Module SW-101U UK, SW-101F French, SW-101G GermanInstalling the Console InstallationInstallation Accessories Order to change the password, follow the procedures below Trouble Shooting InstallationProgramming Passwords Changing PasswordsControl Panel Installation Trouble ShootingSolutions Phone Number ProgrammingHome Automation Testing Phone NumbersEvent Trigger Contact ID Phone numberTable F Zone LED status for erasing control module Account Number ProgrammingErase Control Modules Deactivating the Digital DialerOperation Mounting the Sensor Installing Door / Window SensorsPart 2 Learn signal from Control Panel to Control Module TestingTable E Zone LED status for learning control module Installing Motion SensorInsert Battery Part 1 Learn signal from Control Module to Control PanelLearn Control Modules Control module command signalErase Sensors Alert ModeOperation Advanced ProgrammingTable C MuteLearn Sensors Continue Learn Sensors System StatusArming the System System is now armed Erase Keychain / Keypad RemotesDisarming the system Before the siren soundsDisarming under Duress Learn Keychain / Keypad RemotesDisarming a triggered control panel Phone Line Failure To enable alert zone feature, follow the instructions belowPanic System FailureControl Panel Low BatteryIt is recommend to enable alert zone if Sensor FailureAuto Mute To enable auto mute feature, follow the instructions belowExample CommunicationReceiving the Emergency Call Remote Operation by Telephone To access the control panel away from homeCalling in when you are away from home System Armed Alarm ModeRemote Phone Operations Beep / AlarmSystem Disarmed Alert Mode

ML-001, ML-100 specifications

The SkyLink ML-100 and ML-001 are innovative products in the realm of machine learning and artificial intelligence, designed to simplify the process of deploying and managing machine learning models in various applications. As devices that cater to developers and businesses alike, they bring cutting-edge technologies to the forefront, ensuring a seamless experience for users looking to utilize machine learning effectively.

The SkyLink ML-100 is specifically engineered to provide high-performance capabilities in a compact form factor. One of its main features is the advanced processing unit, which leverages state-of-the-art neural network architectures. This allows the device to handle complex algorithms and process large datasets efficiently. Additionally, the ML-100 is equipped with robust connectivity options, including Wi-Fi, Bluetooth, and support for various IoT protocols, making it an ideal choice for applications in smart homes, industrial automation, and beyond.

On the other hand, the SkyLink ML-001 serves as a versatile platform for developers who wish to train and deploy their machine-learning models. It is designed with a user-friendly interface that supports easy integration with popular programming languages such as Python and R. The ML-001 also boasts an extensive library of pre-built models and algorithms, enabling users to accelerate their development processes. Furthermore, the device comes with advanced data analytics features, providing insightful reports and visualizations that help users understand their model performances better.

Both devices prioritize energy efficiency, ensuring that they can run demanding models without excessive power consumption. They feature adaptive cooling technologies to maintain optimal operating conditions, thereby prolonging device lifespan and enhancing performance stability.

SkyLink incorporates robust security measures into both models, protecting sensitive data and ensuring secure communications. With end-to-end encryption and secure access controls, businesses can rest assured that their data remains confidential.

In conclusion, the SkyLink ML-100 and ML-001 represent significant advancements in machine learning technologies, offering a unique blend of performance, versatility, and security. Whether targeting developers seeking a platform for model deployment or businesses looking for powerful, connected devices, these products stand out in the competitive landscape, providing the tools necessary to harness the full potential of machine learning.
Top Page Image Contents