SkyLink ML-001, ML-100 manual Learn Control Modules, Control module command signal

Page 19
Turn on (command signal)

HOME AUTOMATION

The Control Panel can be used to control lights and home applicances with a Control Module, (Control Module is sold separately). Garage door opener can be controlled with a Garage Door Receiver (sold separately). The Control Panel can control up to 5 Control Modules / Garage Door Receivers.

There are 3 ways to control these modules / receivers:

1. Using the keypad on the control panel to operate these modules / receivers manually

2. Calling in away from home using a touch tone phone (Refer to “Remote Operation by Telephone”)

Door open

Lights

 

on

INSTALLATION (ML-100 Only)

For outdoor monitoring, please refer to page 33 to program the motion sensor to Alert Zone.

You may now close the battery cover and re-insert the screw.

Mount the ball-head joint on the wall with screws provided. Slide the back of the sensor into the ball-head joint. The mounting angle can be adjusted.

Testing

Walk test should be performed after the motion sensor is mounted. Walk in the detected area, if motion is detected, a red light inside the sensor will glow. If the red light does not glow, motion has not been detected and you may need to re-position the sensor. Ensure you walk test all the locations that you would like the motion sensor to cover.

3. Setting up Event Trigger

(Refer to Advanced Programming)

These control modules should be programmed to the control panel as device 1 to 5. Please follow the programming instructions below to program these control modules.

Note:

-Perform the walk test after you have inserted the battery for more than 1 minute.

-Before performing the walk test, the sensor should not detect any motion.

-After motion is detected once, the sensor will not be triggered unless no motion is detected for 20 seconds. Therefore, wait for at least 20 seconds during walk testing between 2 activations.

DETECTING AREA: (Unit = meter)

14

55°

1.2M

 

55°

12

 

11°

10

 

 

8

 

 

6

 

27°

 

22°

22°

4

 

 

2

 

 

M

 

 

 

12°

 

SENSOR

0

1

2

3

4

5

6

7

8

9

10

11

12

13

Learn Control Modules

Both control panel and control module are transceivers, meaning they can transmit and receive signals from each other. For home automation, the user will initiate an action from the control panel, such as sending a signal to turn on the light, then the control module will receive such signal and respond. The control module will then send back a confirmation to the control panel

to indicate the light has been turned on.

Therefore, during programming,

it is required to program 2 things:Control

Module

1.Signal from control module to control panel (confirmation signal)

2. Signal from control panel to

Control

 

Panel

Confirm on

control module (command signal)

 

 

(confirmation

 

 

signal)

Caution:

When installing the motion sensor, avoid placing it near heat or cold producing devices (i.e. A/C or furnace vents, fans, ovens, space heaters, etc). Air movement, especially caused by changes in temperature may trigger the Motion Sensor and cause false alarms. Please carefully test your Motion Sensor so that it will only be triggered by wanted movement.

You have now successfully installed and programmed the Control Panel and its sensors. Please follow the rest of the instructions for operations and advanced programming.

–40–

–17–

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Fax 905 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Tel 905Email support@skylinkhome.com Home Smart Center Important Safety Instructions EMC Declaration of ConformityDisarming a triggered control panel ContentSystem Configuration OperationOverview IntroductionFCC Information Consumer Information System Configuration Emergency Dialer AD-433S AccessoriesControl Module SW-100 Control Module SW-101U UK, SW-101F French, SW-101G GermanInstalling the Console InstallationInstallation Accessories Order to change the password, follow the procedures below Trouble Shooting InstallationProgramming Passwords Changing PasswordsControl Panel Installation Trouble ShootingSolutions Phone Number ProgrammingHome Automation Testing Phone NumbersEvent Trigger Contact ID Phone numberTable F Zone LED status for erasing control module Account Number ProgrammingOperation Deactivating the Digital DialerErase Control Modules Mounting the Sensor Installing Door / Window SensorsPart 2 Learn signal from Control Panel to Control Module TestingTable E Zone LED status for learning control module Installing Motion SensorInsert Battery Part 1 Learn signal from Control Module to Control PanelLearn Control Modules Control module command signalErase Sensors Alert ModeOperation Advanced ProgrammingLearn Sensors Continue MuteTable C Arming the System System StatusLearn Sensors System is now armed Erase Keychain / Keypad RemotesDisarming the system Before the siren soundsDisarming a triggered control panel Learn Keychain / Keypad RemotesDisarming under Duress Phone Line Failure To enable alert zone feature, follow the instructions belowPanic System FailureControl Panel Low BatteryIt is recommend to enable alert zone if Sensor FailureAuto Mute To enable auto mute feature, follow the instructions belowReceiving the Emergency Call CommunicationExample Remote Operation by Telephone To access the control panel away from homeCalling in when you are away from home System Armed Alarm ModeSystem Disarmed Alert Mode Beep / AlarmRemote Phone Operations

ML-001, ML-100 specifications

The SkyLink ML-100 and ML-001 are innovative products in the realm of machine learning and artificial intelligence, designed to simplify the process of deploying and managing machine learning models in various applications. As devices that cater to developers and businesses alike, they bring cutting-edge technologies to the forefront, ensuring a seamless experience for users looking to utilize machine learning effectively.

The SkyLink ML-100 is specifically engineered to provide high-performance capabilities in a compact form factor. One of its main features is the advanced processing unit, which leverages state-of-the-art neural network architectures. This allows the device to handle complex algorithms and process large datasets efficiently. Additionally, the ML-100 is equipped with robust connectivity options, including Wi-Fi, Bluetooth, and support for various IoT protocols, making it an ideal choice for applications in smart homes, industrial automation, and beyond.

On the other hand, the SkyLink ML-001 serves as a versatile platform for developers who wish to train and deploy their machine-learning models. It is designed with a user-friendly interface that supports easy integration with popular programming languages such as Python and R. The ML-001 also boasts an extensive library of pre-built models and algorithms, enabling users to accelerate their development processes. Furthermore, the device comes with advanced data analytics features, providing insightful reports and visualizations that help users understand their model performances better.

Both devices prioritize energy efficiency, ensuring that they can run demanding models without excessive power consumption. They feature adaptive cooling technologies to maintain optimal operating conditions, thereby prolonging device lifespan and enhancing performance stability.

SkyLink incorporates robust security measures into both models, protecting sensitive data and ensuring secure communications. With end-to-end encryption and secure access controls, businesses can rest assured that their data remains confidential.

In conclusion, the SkyLink ML-100 and ML-001 represent significant advancements in machine learning technologies, offering a unique blend of performance, versatility, and security. Whether targeting developers seeking a platform for model deployment or businesses looking for powerful, connected devices, these products stand out in the competitive landscape, providing the tools necessary to harness the full potential of machine learning.
Top Page Image Contents