SkyLink ML-001, ML-100 manual Home Automation, Testing Phone Numbers

Page 13
–11–

HOME AUTOMATION

®

This row

:

Buttons to Disable Event Tigger

Zone LED : Off

 

Press once will enable “Event Trigger On”,

 

press again will enable “Event Trigger Off”.

 

This row of buttons operates in toggle manner,

 

between event trigger on and event trigger off.

This row

:

Buttons to Enable Event Trigger

Zone LED : 1) On (Event Trigger On)

 

 

2) Flash (Event Trigger Off)

 

DISABLE EVENT TRIGGER

ENABLE EVENT TRIGGER

Zone 1

Button [1]

Button [6]

Zone 2

Button [2]

Button [7]

Zone 3

Button [3]

Button [8]

Zone 4

Button [4]

Button [9]

Zone 5

Button [5]

Button [0]

–46–

INSTALLATION

Note:

-It’s not recommended to program 911, fire station or any emergency services phone numbers into any of the phone memories without their approvals.

-Ensure to program a valid phone number and write down the programmed phone number on the System Setting Information provide on the back of this user's instructions.

-You may quit programming by pressing [PROG] button at any time.

-If no phone number is programmed, the ARM LED will continue to flash.

Testing Phone Numbers:

After you have programmed all the phone numbers, you should verify you have programmed the phone numbers correctly. This can be done by triggering the alarm silently by entering the duress password, so it dials to the programmed phone numbers without sounding the alarm.

Note:

You must inform the recipients of the programmed phone numbers, so they know what to expect when they receive the phone call from the control panel during an emergency. These recipients should know the password to your control panel if you expect them to have remote access of your control panel. For more informa- tion regarding receiving the emergency call, please refer to page 26.

1.Press [Arm], you should hear beeping from the control panel.

2.Press [3838]. Beeping will stop, and the control panel will start to dial the first number.

3.The called party should receive the call. Pick up the call and say “Hello”, an emergency message “System Panic” will be played. If the programmed phone doesn’t ring, ensure the phone number is programmed correctly, or reprogram this phone number again.

4.After the emergency message has been played for several times (depending on how many times it was programmed), the called party will hear “Enter Password”.

5.Enter either the master password or secondary password. If the correct password is accepted, you will hear “Password Accepted”, otherwise, you will hear “Password Failure”.

6.Press [0][#] on the telephone to hang up.

7.The control panel will start to dial the next programmed phone number.

Note:

-Refer to page 26 [Receiving the Emergency Call] for more info on how to react to an emergency call.

-The password is treated as a confirmation of the emergency message. Once a valid password is entered, the control panel will not call that number again, it will proceed to the next number.

-If any one of the called parties disarms the control panel, the control panel will not continue to dial the remaining phone numbers.

-After calling all the programmed phone numbers, the control panel will be back to the previous operation mode.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Fax 905 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Tel 905Email support@skylinkhome.com Home Smart Center Important Safety Instructions EMC Declaration of ConformitySystem Configuration ContentOperation Disarming a triggered control panelOverview IntroductionFCC Information Consumer Information System Configuration Control Module SW-100 AccessoriesControl Module SW-101U UK, SW-101F French, SW-101G German Emergency Dialer AD-433SInstalling the Console InstallationInstallation Accessories Programming Passwords Trouble Shooting InstallationChanging Passwords Order to change the password, follow the procedures belowSolutions Installation Trouble ShootingPhone Number Programming Control PanelHome Automation Testing Phone NumbersEvent Trigger Contact ID Phone numberTable F Zone LED status for erasing control module Account Number ProgrammingOperation Deactivating the Digital DialerErase Control Modules Part 2 Learn signal from Control Panel to Control Module Installing Door / Window SensorsTesting Mounting the SensorInsert Battery Installing Motion SensorPart 1 Learn signal from Control Module to Control Panel Table E Zone LED status for learning control moduleLearn Control Modules Control module command signalOperation Alert ModeAdvanced Programming Erase SensorsLearn Sensors Continue MuteTable C Arming the System System StatusLearn Sensors Disarming the system Erase Keychain / Keypad RemotesBefore the siren sounds System is now armedDisarming a triggered control panel Learn Keychain / Keypad RemotesDisarming under Duress Panic To enable alert zone feature, follow the instructions belowSystem Failure Phone Line FailureIt is recommend to enable alert zone if Low BatterySensor Failure Control PanelAuto Mute To enable auto mute feature, follow the instructions belowReceiving the Emergency Call CommunicationExample Calling in when you are away from home To access the control panel away from homeSystem Armed Alarm Mode Remote Operation by TelephoneSystem Disarmed Alert Mode Beep / AlarmRemote Phone Operations

ML-001, ML-100 specifications

The SkyLink ML-100 and ML-001 are innovative products in the realm of machine learning and artificial intelligence, designed to simplify the process of deploying and managing machine learning models in various applications. As devices that cater to developers and businesses alike, they bring cutting-edge technologies to the forefront, ensuring a seamless experience for users looking to utilize machine learning effectively.

The SkyLink ML-100 is specifically engineered to provide high-performance capabilities in a compact form factor. One of its main features is the advanced processing unit, which leverages state-of-the-art neural network architectures. This allows the device to handle complex algorithms and process large datasets efficiently. Additionally, the ML-100 is equipped with robust connectivity options, including Wi-Fi, Bluetooth, and support for various IoT protocols, making it an ideal choice for applications in smart homes, industrial automation, and beyond.

On the other hand, the SkyLink ML-001 serves as a versatile platform for developers who wish to train and deploy their machine-learning models. It is designed with a user-friendly interface that supports easy integration with popular programming languages such as Python and R. The ML-001 also boasts an extensive library of pre-built models and algorithms, enabling users to accelerate their development processes. Furthermore, the device comes with advanced data analytics features, providing insightful reports and visualizations that help users understand their model performances better.

Both devices prioritize energy efficiency, ensuring that they can run demanding models without excessive power consumption. They feature adaptive cooling technologies to maintain optimal operating conditions, thereby prolonging device lifespan and enhancing performance stability.

SkyLink incorporates robust security measures into both models, protecting sensitive data and ensuring secure communications. With end-to-end encryption and secure access controls, businesses can rest assured that their data remains confidential.

In conclusion, the SkyLink ML-100 and ML-001 represent significant advancements in machine learning technologies, offering a unique blend of performance, versatility, and security. Whether targeting developers seeking a platform for model deployment or businesses looking for powerful, connected devices, these products stand out in the competitive landscape, providing the tools necessary to harness the full potential of machine learning.
Top Page Image Contents