SkyLink ML-100, ML-001 manual Sensor Failure, Low Battery, Control Panel

Page 26

OPERATION

Sensor Failure

ADVANCED PROGRAMMING

The control panel constantly monitors its sensors, if the control panel fails to communicate with any sensors, it will notify the user by:

1.The zone LED of the failed sensor will be on steadily;

2.Voice announcement “zone X sensor Y failure” will be played.

When sensor failure occurs, try the following:

1.

Check if the sensor is located at where it should be, and whether there is any

 

physical damage to the sensor.

2.

If the failed sensor is not physically damaged, try to activate the sensor and see

 

if the control panel reacts to such activation.

3.

If not, try to remove the sensor from its location, and bring it closer to control

 

DISABLE

ENABLE

 

AUTO MUTE AUTO MUTE

Zone 1

Button [1]

Button [6]

Zone 2

Button [2]

Button [7]

Zone 3

Button [3]

Button [8]

Zone 4

Button [4]

Button [9]

Zone 5

Button [5]

Button [0]

®

This row : Buttons to Disable Auto Mute

Zone LED : Flash

This row : Buttons to Enable Auto Mute

Zone LED : ON

panel and activate the sensor. It is possible that the sensor is installed too far

from the control panel and it cannot establish a steady communication with the

control panel. If this is the case, please install the sensor closer to the control

panel.

Low Battery

Control Panel

The control panel is powered mainly by the adapter. However, during power outage, it will be powered by the rechargeable backup battery. Under standby conditions, these batteries can last for 48 hours.

When the backup battery is running low, the “LO BATT” LED on the control panel will be on, indicating the backup battery should be recharged. To recharge the backup battery, plug in the power adapter. It takes approx. 20 hours to fully charge the backup battery.

Sensors (For ML-100 Only)

All of the sensors are battery powered. Depending on the operating condition and environment, the battery life varies from 9 months to 2 years. 9V alkaline battery is used for the motion sensor, the battery life is approximately 9 months. Door / Window Sensor operates on a Lithium CR-2032 battery, with battery life of approximately 2 years. For other sensors, please refer to the user’s instructions regarding the battery life.

Alert Zone (Bypass Zone)

As explained earlier, the control panel can operate in 2 different modes, 1) Alert Mode, 2) Alarm Mode. In alarm mode, when a sensor is triggered, the control panel will either give a 30 seconds entry delay, or siren will sound immediately (with instant alarm). However, there are sensors that you do not want to trigger the alarm when the system is armed. Such as an outdoor sensor, or any other sensors that you only want to give you alert notification. Under such circum- stances, zone(s) can be programed to react only when the control panel is in alert mode, these zones will be automatically bypassed when the control panel is in alarm mode. These zones can also be considered as "Bypass zones".

It is recommend to enable alert zone if:

-You do not consider the sensors in that zone an emergency

-Sensors in that zone are located outdoors

-When nobody is home, you do not want to know the status of the sensor(s) in that zone

Factory Default: This feature was disabled for all zones at the factory.

24

33

Image 26
Contents Email support@skylinkhome.com Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Tel 905Fax 905 Home Smart Center Important Safety Instructions Declaration of Conformity EMCOperation ContentSystem Configuration Disarming a triggered control panelFCC Information Consumer Information IntroductionOverview System Configuration Control Module SW-101U UK, SW-101F French, SW-101G German AccessoriesControl Module SW-100 Emergency Dialer AD-433SInstallation Installing the ConsoleInstallation Accessories Changing Passwords Trouble Shooting InstallationProgramming Passwords Order to change the password, follow the procedures belowPhone Number Programming Installation Trouble ShootingSolutions Control PanelTesting Phone Numbers Home AutomationContact ID Phone number Event TriggerAccount Number Programming Table F Zone LED status for erasing control moduleErase Control Modules Deactivating the Digital DialerOperation Testing Installing Door / Window SensorsPart 2 Learn signal from Control Panel to Control Module Mounting the SensorPart 1 Learn signal from Control Module to Control Panel Installing Motion SensorInsert Battery Table E Zone LED status for learning control moduleControl module command signal Learn Control ModulesAdvanced Programming Alert ModeOperation Erase SensorsTable C MuteLearn Sensors Continue Learn Sensors System StatusArming the System Before the siren sounds Erase Keychain / Keypad RemotesDisarming the system System is now armedDisarming under Duress Learn Keychain / Keypad RemotesDisarming a triggered control panel System Failure To enable alert zone feature, follow the instructions belowPanic Phone Line FailureSensor Failure Low BatteryIt is recommend to enable alert zone if Control PanelTo enable auto mute feature, follow the instructions below Auto MuteExample CommunicationReceiving the Emergency Call System Armed Alarm Mode To access the control panel away from homeCalling in when you are away from home Remote Operation by TelephoneRemote Phone Operations Beep / AlarmSystem Disarmed Alert Mode

ML-001, ML-100 specifications

The SkyLink ML-100 and ML-001 are innovative products in the realm of machine learning and artificial intelligence, designed to simplify the process of deploying and managing machine learning models in various applications. As devices that cater to developers and businesses alike, they bring cutting-edge technologies to the forefront, ensuring a seamless experience for users looking to utilize machine learning effectively.

The SkyLink ML-100 is specifically engineered to provide high-performance capabilities in a compact form factor. One of its main features is the advanced processing unit, which leverages state-of-the-art neural network architectures. This allows the device to handle complex algorithms and process large datasets efficiently. Additionally, the ML-100 is equipped with robust connectivity options, including Wi-Fi, Bluetooth, and support for various IoT protocols, making it an ideal choice for applications in smart homes, industrial automation, and beyond.

On the other hand, the SkyLink ML-001 serves as a versatile platform for developers who wish to train and deploy their machine-learning models. It is designed with a user-friendly interface that supports easy integration with popular programming languages such as Python and R. The ML-001 also boasts an extensive library of pre-built models and algorithms, enabling users to accelerate their development processes. Furthermore, the device comes with advanced data analytics features, providing insightful reports and visualizations that help users understand their model performances better.

Both devices prioritize energy efficiency, ensuring that they can run demanding models without excessive power consumption. They feature adaptive cooling technologies to maintain optimal operating conditions, thereby prolonging device lifespan and enhancing performance stability.

SkyLink incorporates robust security measures into both models, protecting sensitive data and ensuring secure communications. With end-to-end encryption and secure access controls, businesses can rest assured that their data remains confidential.

In conclusion, the SkyLink ML-100 and ML-001 represent significant advancements in machine learning technologies, offering a unique blend of performance, versatility, and security. Whether targeting developers seeking a platform for model deployment or businesses looking for powerful, connected devices, these products stand out in the competitive landscape, providing the tools necessary to harness the full potential of machine learning.