SkyLink ML-001, ML-100 Remote Operation by Telephone, To access the control panel away from home

Page 29

ADVANCED PROGRAMMING

System Armed (Alarm Mode)

If a zone is set to “Beep”, the control panel will give entry / exit delay.

If a zone is set to “Alarm”, the siren will sound immediately without entry delay

-Alarm Mode (System Armed): If a sensor is triggered (i.e. opening a door) with the alarm setting on, the siren will sound immediately without entry delay, it is called “Instant Alarm”. The siren will not stop until the siren timeout or a valid password is entered. Control panel will call the emergency phone numbers to notify the users of the alarm situation.

When a sensor is triggered, there are 4 options:

 

ZONE SETTING

OPERATING MODE

BEEP

ALARM

Disarmed (Alert)

1) Beep

2)

Alarm sounds immediately

Armed (Alarm)

3) Entry / Exit Delay

4)

Alarm sounds and calls

 

 

 

preprogrammed phone

 

 

 

numbers immediately

Factory Default: All zones were programmed to Beep at the factory.

You may consider to programming the zone(s) into Alarm mode if:

-You need immediate attention if that sensor is triggered, such as flood sensor, smoke sensor etc.

-The sensor will not be triggered on a daily basis, such as a door that you normally will not open, and if it opens, you would like to know immediately.

Caution:

It is not recommended to program an outdoor sensor to Alarm mode, which may cause false alarm. For outdoor sensors, they should be programmed into an Alert Zone, please refer to page 33 for details.

COMMUNICATION

Remote Operation by Telephone

The control panel can be operated while you are away from home. You can have access to the control panel with any touch tone phone to perform a variety of operations, listed below.

-Arm

-Disarm

-Lights, Home Applicances on / off (Requires additonal Control Module)

-Garage door open / close (Requires additional Garage Door Receiver)

-System status

-Disconnect

There are 2 ways you can have access to the remote phone operation:

1.You can call the control panel when you are away from home; or

2.When the control panel calls you during emergency.

To access the control panel away from home

Calling in when you are away from home

1.Call your home phone number, or the number that the phone line of the control panel is connected to.

2.Hang up after the second ring.

3.Wait at least 10 seconds, but not more than 40 seconds, then call the phone number again.

4.The control panel will pick up the phone call and request for a valid user password, you will hear “Enter Password”. You can enter either the Master Password or Secondary Password. If the password is correct, you will hear “Password Accepted”, otherwise, you will hear “Password Failure”.

5.Once the password is accepted, you can have access to all the operations listed below.

–30–

–27–

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Email support@skylinkhome.com Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Tel 905Fax 905 Home Smart Center Important Safety Instructions EMC Declaration of ConformitySystem Configuration ContentOperation Disarming a triggered control panelFCC Information Consumer Information IntroductionOverview System Configuration Control Module SW-100 AccessoriesControl Module SW-101U UK, SW-101F French, SW-101G German Emergency Dialer AD-433SInstalling the Console InstallationInstallation Accessories Programming Passwords Trouble Shooting InstallationChanging Passwords Order to change the password, follow the procedures belowSolutions Installation Trouble ShootingPhone Number Programming Control PanelHome Automation Testing Phone NumbersEvent Trigger Contact ID Phone numberTable F Zone LED status for erasing control module Account Number ProgrammingErase Control Modules Deactivating the Digital DialerOperation Part 2 Learn signal from Control Panel to Control Module Installing Door / Window SensorsTesting Mounting the SensorInsert Battery Installing Motion SensorPart 1 Learn signal from Control Module to Control Panel Table E Zone LED status for learning control moduleLearn Control Modules Control module command signalOperation Alert ModeAdvanced Programming Erase SensorsTable C MuteLearn Sensors Continue Learn Sensors System StatusArming the System Disarming the system Erase Keychain / Keypad RemotesBefore the siren sounds System is now armedDisarming under Duress Learn Keychain / Keypad RemotesDisarming a triggered control panel Panic To enable alert zone feature, follow the instructions belowSystem Failure Phone Line FailureIt is recommend to enable alert zone if Low BatterySensor Failure Control PanelAuto Mute To enable auto mute feature, follow the instructions belowExample CommunicationReceiving the Emergency Call Calling in when you are away from home To access the control panel away from homeSystem Armed Alarm Mode Remote Operation by TelephoneRemote Phone Operations Beep / AlarmSystem Disarmed Alert Mode

ML-001, ML-100 specifications

The SkyLink ML-100 and ML-001 are innovative products in the realm of machine learning and artificial intelligence, designed to simplify the process of deploying and managing machine learning models in various applications. As devices that cater to developers and businesses alike, they bring cutting-edge technologies to the forefront, ensuring a seamless experience for users looking to utilize machine learning effectively.

The SkyLink ML-100 is specifically engineered to provide high-performance capabilities in a compact form factor. One of its main features is the advanced processing unit, which leverages state-of-the-art neural network architectures. This allows the device to handle complex algorithms and process large datasets efficiently. Additionally, the ML-100 is equipped with robust connectivity options, including Wi-Fi, Bluetooth, and support for various IoT protocols, making it an ideal choice for applications in smart homes, industrial automation, and beyond.

On the other hand, the SkyLink ML-001 serves as a versatile platform for developers who wish to train and deploy their machine-learning models. It is designed with a user-friendly interface that supports easy integration with popular programming languages such as Python and R. The ML-001 also boasts an extensive library of pre-built models and algorithms, enabling users to accelerate their development processes. Furthermore, the device comes with advanced data analytics features, providing insightful reports and visualizations that help users understand their model performances better.

Both devices prioritize energy efficiency, ensuring that they can run demanding models without excessive power consumption. They feature adaptive cooling technologies to maintain optimal operating conditions, thereby prolonging device lifespan and enhancing performance stability.

SkyLink incorporates robust security measures into both models, protecting sensitive data and ensuring secure communications. With end-to-end encryption and secure access controls, businesses can rest assured that their data remains confidential.

In conclusion, the SkyLink ML-100 and ML-001 represent significant advancements in machine learning technologies, offering a unique blend of performance, versatility, and security. Whether targeting developers seeking a platform for model deployment or businesses looking for powerful, connected devices, these products stand out in the competitive landscape, providing the tools necessary to harness the full potential of machine learning.
Top Page Image Contents