SkyLink ML-001, ML-100 manual Auto Mute, To enable auto mute feature, follow the instructions below

Page 27

ADVANCED PROGRAMMING

Auto Mute

When a sensor is triggered in alert mode, audio warning will be emitted, either beep or alarm. For example, if a door is opened, the beep will not stop until the door is closed. If the door is open for 2 hours, the beep will go on for 2 hours.

There are times that this is not desired. With the auto mute feature enabled, the beep will go on for only 20 seconds. After that, even if the sensor remains open, the beep will stop only the zone LED will flash to indicate the sensor is triggered. Beep will go on again if the sensor is closed and opened again.

Note: Auto Mute only functions when the control panel is in alert mode (disarmed). If the control panel is in alarm mode (armed), a triggered sensor will result in entry delay or instant alarm.

Factory Default: This feature was disabled for all zones at the factory.

To enable auto mute feature, follow the instructions below.

Step

Keys

Function

Description

Note

1

[PROG]

Enter Program-

Enter master

3 beeps for valid

[MPIN]

ming mode

password to

password. 1 long beep

 

 

 

 

programming mode

for invalid password.

2

[6]

Select Auto Mute

 

After [6] is entered, some

 

Enable / Disable

 

zone LEDs will flash or

 

 

 

stay on. This indicates whether Auto Mute is enabled or disabled.

OPERATION

When the sensor is running low in battery, the sensor will send a wireless low battery signal to the control panel. The zone LED representing that sensor will be on steadily, indicating sensor(s) in that zone is in trouble condition. Control Panel will also have an announcement to advise the user the trouble condition is low battery, such as “zone X sensor Y low battery”, where X and Y represent the zone and sensor number. Please replace the battery of that sensor.

Keychain Remote (For ML-100 Only)

The battery of the keychain remote (Alkaline, Type 23A, 12V) needs to be replaced when either one of the followings occurs:

1.The LED on the keychain doesn’t flash or on when a key is pressed; or

2.The operating range starts to decrease.

To replace the battery:

1. Undo the two screws on the back of the transmitter. The bottom case will then come off.

2. Using a small screwdriver or pen, pry out the old battery from one end.

3. Place the new battery in position. A diagram in the battery compartment indicates which end is positive and which is negative.

4. Close the battery cover and reinsert two screws.

-

 

3

Disable

Select which

 

Auto Mute:

zone you would

[1]to [5] like to enable / disable auto mute.

Enable Auto Mute: [6] to [0].

Refer to the diagram below to select the appropriate setting.

If auto mute is enabled, that zone LED will be on. If it is disabled, the LED will flash. You are allow to make multiple changes before terminating programming mode.

+

4

[PROG]

Terminate

PROG LED will be off, and

 

when

programming

you will hear 3 beeps.

 

finished.

mode.

 

32

25

Image 27
Contents Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Tel 905 Fax 905Email support@skylinkhome.com Home Smart Center Important Safety Instructions EMC Declaration of ConformityDisarming a triggered control panel ContentSystem Configuration OperationIntroduction OverviewFCC Information Consumer Information System Configuration Emergency Dialer AD-433S AccessoriesControl Module SW-100 Control Module SW-101U UK, SW-101F French, SW-101G GermanInstalling the Console InstallationInstallation Accessories Order to change the password, follow the procedures below Trouble Shooting InstallationProgramming Passwords Changing PasswordsControl Panel Installation Trouble ShootingSolutions Phone Number ProgrammingHome Automation Testing Phone NumbersEvent Trigger Contact ID Phone numberTable F Zone LED status for erasing control module Account Number ProgrammingDeactivating the Digital Dialer OperationErase Control Modules Mounting the Sensor Installing Door / Window SensorsPart 2 Learn signal from Control Panel to Control Module TestingTable E Zone LED status for learning control module Installing Motion SensorInsert Battery Part 1 Learn signal from Control Module to Control PanelLearn Control Modules Control module command signalErase Sensors Alert ModeOperation Advanced ProgrammingMute Learn Sensors ContinueTable C System Status Arming the SystemLearn Sensors System is now armed Erase Keychain / Keypad RemotesDisarming the system Before the siren soundsLearn Keychain / Keypad Remotes Disarming a triggered control panelDisarming under Duress Phone Line Failure To enable alert zone feature, follow the instructions belowPanic System FailureControl Panel Low BatteryIt is recommend to enable alert zone if Sensor FailureAuto Mute To enable auto mute feature, follow the instructions belowCommunication Receiving the Emergency CallExample Remote Operation by Telephone To access the control panel away from homeCalling in when you are away from home System Armed Alarm ModeBeep / Alarm System Disarmed Alert ModeRemote Phone Operations

ML-001, ML-100 specifications

The SkyLink ML-100 and ML-001 are innovative products in the realm of machine learning and artificial intelligence, designed to simplify the process of deploying and managing machine learning models in various applications. As devices that cater to developers and businesses alike, they bring cutting-edge technologies to the forefront, ensuring a seamless experience for users looking to utilize machine learning effectively.

The SkyLink ML-100 is specifically engineered to provide high-performance capabilities in a compact form factor. One of its main features is the advanced processing unit, which leverages state-of-the-art neural network architectures. This allows the device to handle complex algorithms and process large datasets efficiently. Additionally, the ML-100 is equipped with robust connectivity options, including Wi-Fi, Bluetooth, and support for various IoT protocols, making it an ideal choice for applications in smart homes, industrial automation, and beyond.

On the other hand, the SkyLink ML-001 serves as a versatile platform for developers who wish to train and deploy their machine-learning models. It is designed with a user-friendly interface that supports easy integration with popular programming languages such as Python and R. The ML-001 also boasts an extensive library of pre-built models and algorithms, enabling users to accelerate their development processes. Furthermore, the device comes with advanced data analytics features, providing insightful reports and visualizations that help users understand their model performances better.

Both devices prioritize energy efficiency, ensuring that they can run demanding models without excessive power consumption. They feature adaptive cooling technologies to maintain optimal operating conditions, thereby prolonging device lifespan and enhancing performance stability.

SkyLink incorporates robust security measures into both models, protecting sensitive data and ensuring secure communications. With end-to-end encryption and secure access controls, businesses can rest assured that their data remains confidential.

In conclusion, the SkyLink ML-100 and ML-001 represent significant advancements in machine learning technologies, offering a unique blend of performance, versatility, and security. Whether targeting developers seeking a platform for model deployment or businesses looking for powerful, connected devices, these products stand out in the competitive landscape, providing the tools necessary to harness the full potential of machine learning.