Furuno FM-3000 manual Function Display

Page 12

1.Controls

1.2 Function Display

 

o

i

 

q BUSY/TRANSMIT INDICATOR (p. 7)

 

 

 

 

 

➥“BUSY” appears when receiving a signal or when the

 

 

 

 

 

squelch opens.

q

BUSY

INT

 

 

➥“TX” appears while transmitting.

 

 

w

25W

CALL

 

w POWER INDICATOR (p. 7)

e

TAG SC

DUP

 

 

➥“25W” appears when high power is selected.

r

CALLING

 

 

 

 

 

 

➥“1W” appears when low power is selected.

 

t y

u

e TAG CHANNEL INDICATOR (p. 12)

 

Appears when a tag channel is selected.

 

 

 

 

 

r CHANNEL COMMENT INDICATOR

➥Channel comment appears if programmed. (p. 8)

➥“Low Battery” blinks when the battery voltage drops to approx. 10 V DC or below.

➥“DUAL” appears during Dualwatch; “TRI” appears dur- ing Tri-watch. (p. 10)

t SCRAMBLER INDICATOR (p. 9)

Appears when an optional Voice scrambler is activated.

3

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Marine VHF Radiotelephone Foreword FM-3000Case of Emergency Do not open the equipment Do not disassemble or modify the equipmentAny repair work must be done by a licensed radio technician Only qualified personal should work in- side the equipment Standard SteerlingCompass TransceiverTable of Contents Setting Tag Channels Set Mode ProgrammingInstallation Panel DescriptionSystem Configulation Vii Standard supply & Options Standard supply Options Controls Front PanelSQL control p HI/LO keyLO/DX IC SCR key 16 9 keyDistress key CH/WX DW U/I/C keyFunction Display Microphone Basic Operation Channel SelectionChannel Channel 9 Call channelPush once When Weather alert is OFF A. channels Or twice Weather channelsChange the channel group, if necessary Rotate Channel to select a channelPush HI/LO to select the output power, if necessary Receiving and TransmittingCall Channel Programming Channel CommentsPush Set mode Scrambler code item Optional Voice Scrambler OperationActivating the Scrambler Programming scrambler codesDualwatch/Tri-Watch DescriptionOperation Again Example Operating Tri-watch on INT ChannelScan Operation Scan TypesSetting Tag Channels Convinient Clearing setting all tagged channelsStarting a Scan Scan startsDSC Operation Mmsi Code ProgrammingDSC Individual ID Programming Address ID/Group IDDeleting Address ID/Group ID Set the individual ID and ID nameRotate Channel to select the desired ID name for deleting Edit the digit of your latitude data by using Channel Edit the digit of your longitude data by using ChannelEdit the digit of the current UTC time by using CHAN- NEL Push DSC/ENT to set the time, and exit the DSC menuPosition/Time Indication Sentence formatteres ‘GGA,’ ‘GNS,’ ‘GLL’Distress alert contains default Distress CallSimple call Normal call Push Distress for 5 sec. to transmit the Distress call Transmitting DSC Calls Transmitting Individual callPush DSC/ENT to transmit the Individual call Transmitting Individual acknowledgement Indv ACK Transmitting Group call Push DSC/ENT to transmit the Group callTransmitting All Ships call Push DSC/ENT to transmit the All Ships callTransmitting Position Request call Push DSC/ENT to transmit the Position Request callTransmitting Position Report call Transmitting Position Reply call Transmitting Position Report Reply callPush DSC/ENT to transmit the Position Report call Receiving DSC Calls Receiving a Distress callReceiving a Distress acknowledgement Receiving an Individual callReceiving an All Ships call Receiving a Distress Relay callReceiving a Geographical Area call Receiving a Position Request call Receiving a Position Report callReceiving a Position Reply call Receiving a Position Report Reply callReceived Messages Distress messageRotate Channel to select Distress, push DSC/ENT Rotate Channel to scroll the messageOther messages Rotate Channel to select Other, push DSC/ENTDSC Set Mode Offset timeRotate Channel to select Offset time, push DSC/ENT Push DSC/ENT to program and to exit the DSC menuMmsi code check Rotate Channel to select Mmsi Check, push DSC/ENTCheck the 9-digit Mmsi DSC self ID code Push DSC/ENT to exit the DSC menuPush LO/DX IC SCR for 1 sec. to enter Intercom mode Other FunctionsIntercom Operation FM-3000 callerMicrophone Lock Function Display BacklightingSet Mode Set Mode ProgrammingAuto ACK items are not selectable when using FM-3010 Set Mode Items Scan modeScan resume timer Weather alertThis item adjusts the contrast of the LCD in 8 steps DSC watchBeep tone Internal speakerAttenuation level Scrambler codeAutomatic acknowledgement Connections and Maintenance Fuse ReplacementCleaning Antenna ConnectionsAntenna Connector Nmea in Red/NMEA OUT White JacksExternal Speaker Jack Using the supplied mounting bracket Mounting the TransceiverUsing the optional FM-3040 Attach the clamps on either side of the FM-3000Optional Unit Installation Dimensions 145.0 5 23⁄32 103.0 110.0 4 11⁄32 165.0 6 1⁄253.0 ⁄32 Unit mm Troubleshooting Problem Possible Cause Solution† Low power only Channel ListOperating Rules Radio license for boaters U.S.A. onlySpecifications SpecificationsGeneral TransmitterPTT Switch PTT pgs Panel DescriptionFront and side keys Channel UP/DOWN Keys Y/ZVOLUME/DIMMER KEY VOL DIM CHANNEL/DUALWATCH/TRI-WATCH KEY CH/WX DW U/I/CLO/DX IC SCR SQUELCH/MONITOR/LOCK KEY SQL Moni LTop keys Volume Indicator p Squelch Indicator pScan Indicator pgs 1DUAL/TRI Watch Indicator pgsCall channel 13.3 3 Weather channelsChannel group A. channelsTurn power on Set output Push H/L to select the output power, if necessaryPush Y/Z to select the desired channel Push Y/Z to adjust the backlight level Lock FunctionsActivating the Lock function Activating the All key lock functionMonitor Function RF Attenuator FunctionPush LO/DX to turn the RF Attenuator function on and OFF Push CH/WX DW U/I/C severalDualwatch/Tri-watch Operation Programming scramble codesPush Y/Z to select the desired channel LO/DX IC SCR to turnTo cancel the tag channel setting, push Scan TAG for 1 sec Convenient Clearing setting all tagged channelsTo stop the scan, push Scan TAG Entering Set mode Turn power OFF While pushing 16 9 , turn power onBeep tone Beep Intercom beep function Push SQL to move to forward then push Y/Z to seAvailable characters 13.17 FM-3010 supplied accessories Accessories included with the FM-3010 QtyConnection cable FM-3011 6 m 20 ft Installation Completed installation should look like thisMm 3⁄32˝ 165 mm 61⁄2 149 mm 57⁄8 R11 Mm 3⁄32
Top Page Image Contents