Furuno FM-3000 manual Installation, Completed installation should look like this

Page 73

13.18 Installation

The optional FM-3010 can be connected to the transceiver directly, as well as via the supplied connection cable for longer distance remote operation. The connector of the con- nection cable can be installed into a cabinet, wall, etc., as a built-in plug.

For longer distance remote operation, the optional extension cable, FM-3020 (6 m; 20 ft/connecting between transceiver and the connection cable), is available, and up to 2 FM-3020 can be added.

qInsert the supplied cable into the external microphone jack and tighten the cable nut as shown below.

13. FM-3010 CONTROLLABLE MIC

wTo use the supplied cable as a wall socket, follow the below steps.

eUsing the mounting base, carefully mark off the 2 spots

where the cable and screws will be fastened.

rDrill holes at these marks.

tInstall the mounting base using the supplied screws as shown below.

Mounting base

Nut

Gasket
Screw holes
(approx. 2 (d) mm; 3⁄32″)	Cap

yThe completed installation should look like this.

Image 73

Contents Marine VHF Radiotelephone FM-3000 ForewordCase of Emergency Do not disassemble or modify the equipment Do not open the equipmentAny repair work must be done by a licensed radio technician Standard Steerling Only qualified personal should work in- side the equipmentCompass TransceiverTable of Contents Set Mode Programming Setting Tag ChannelsInstallation Panel DescriptionVii System ConﬁgulationStandard supply Standard supply & OptionsOptions Front Panel ControlsSQL control p HI/LO key16 9 key LO/DX IC SCR keyDistress key CH/WX DW U/I/C keyFunction Display Microphone Channel Selection Basic OperationChannel Channel 9 Call channelWeather channels Push once When Weather alert is OFF A. channels Or twiceChange the channel group, if necessary Rotate Channel to select a channelReceiving and Transmitting Push HI/LO to select the output power, if necessaryChannel Comments Call Channel ProgrammingPush Optional Voice Scrambler Operation Set mode Scrambler code itemActivating the Scrambler Programming scrambler codesDescription Dualwatch/Tri-WatchOperation Again Example Operating Tri-watch on INT ChannelScan Types Scan OperationConvinient Clearing setting all tagged channels Setting Tag ChannelsStarting a Scan Scan startsMmsi Code Programming DSC OperationDSC Individual ID Programming Address ID/Group IDSet the individual ID and ID name Deleting Address ID/Group IDRotate Channel to select the desired ID name for deleting Edit the digit of your longitude data by using Channel Edit the digit of your latitude data by using ChannelEdit the digit of the current UTC time by using CHAN- NEL Push DSC/ENT to set the time, and exit the DSC menuSentence formatteres ‘GGA,’ ‘GNS,’ ‘GLL’ Position/Time IndicationDistress Call Distress alert contains defaultSimple call Normal call Push Distress for 5 sec. to transmit the Distress call Transmitting Individual call Transmitting DSC CallsPush DSC/ENT to transmit the Individual call Transmitting Individual acknowledgement Indv ACK Push DSC/ENT to transmit the Group call Transmitting Group callPush DSC/ENT to transmit the All Ships call Transmitting All Ships callPush DSC/ENT to transmit the Position Request call Transmitting Position Request callTransmitting Position Report call Transmitting Position Report Reply call Transmitting Position Reply callPush DSC/ENT to transmit the Position Report call Receiving a Distress call Receiving DSC CallsReceiving a Distress acknowledgement Receiving an Individual callReceiving a Distress Relay call Receiving an All Ships callReceiving a Geographical Area call Receiving a Position Report call Receiving a Position Request callReceiving a Position Reply call Receiving a Position Report Reply callDistress message Received MessagesRotate Channel to select Distress, push DSC/ENT Rotate Channel to scroll the messageRotate Channel to select Other, push DSC/ENT Other messagesOffset time DSC Set ModeRotate Channel to select Offset time, push DSC/ENT Push DSC/ENT to program and to exit the DSC menuRotate Channel to select Mmsi Check, push DSC/ENT Mmsi code checkCheck the 9-digit Mmsi DSC self ID code Push DSC/ENT to exit the DSC menuOther Functions Push LO/DX IC SCR for 1 sec. to enter Intercom modeIntercom Operation FM-3000 callerDisplay Backlighting Microphone Lock FunctionSet Mode Programming Set ModeAuto ACK items are not selectable when using FM-3010 Scan mode Set Mode ItemsScan resume timer Weather alertDSC watch This item adjusts the contrast of the LCD in 8 stepsBeep tone Internal speakerScrambler code Attenuation levelAutomatic acknowledgement Fuse Replacement Connections and MaintenanceCleaning Antenna ConnectionsNmea in Red/NMEA OUT White Jacks Antenna ConnectorExternal Speaker Jack Mounting the Transceiver Using the supplied mounting bracketAttach the clamps on either side of the FM-3000 Using the optional FM-3040Optional Unit Installation 145.0 5 23⁄32 103.0 110.0 4 11⁄32 165.0 6 1⁄2 Dimensions53.0 ⁄32 Unit mm Problem Possible Cause Solution TroubleshootingChannel List † Low power onlyRadio license for boaters U.S.A. only Operating RulesSpeciﬁcations SpeciﬁcationsGeneral TransmitterPanel Description PTT Switch PTT pgsFront and side keys Channel UP/DOWN Keys Y/ZCHANNEL/DUALWATCH/TRI-WATCH KEY CH/WX DW U/I/C VOLUME/DIMMER KEY VOL DIMLO/DX IC SCR SQUELCH/MONITOR/LOCK KEY SQL Moni LTop keys Squelch Indicator p Volume Indicator pScan Indicator pgs 1DUAL/TRI Watch Indicator pgs13.3 3 Weather channels Call channelChannel group A. channelsPush H/L to select the output power, if necessary Turn power on Set outputPush Y/Z to select the desired channel Lock Functions Push Y/Z to adjust the backlight levelActivating the Lock function Activating the All key lock functionRF Attenuator Function Monitor FunctionPush LO/DX to turn the RF Attenuator function on and OFF Push CH/WX DW U/I/C severalProgramming scramble codes Dualwatch/Tri-watch OperationPush Y/Z to select the desired channel LO/DX IC SCR to turnConvenient Clearing setting all tagged channels To cancel the tag channel setting, push Scan TAG for 1 secTo stop the scan, push Scan TAG Turn power OFF While pushing 16 9 , turn power on Entering Set modeBeep tone Beep Push SQL to move to forward then push Y/Z to se Intercom beep functionAvailable characters Accessories included with the FM-3010 Qty 13.17 FM-3010 supplied accessoriesConnection cable FM-3011 6 m 20 ft Completed installation should look like this InstallationMm 3⁄32˝ R11 Mm 3⁄32 165 mm 61⁄2 149 mm 57⁄8