Furuno FM-3000 manual Do not open the equipment, Do not disassemble or modify the equipment

Page 4
BE CAREFUL!

RSAFTY INSTRUCTION

For the operator

RCAUTION

Do not open the equipment.

Only qualified personal should work inside the equipment.

Do not disassemble or modify the equipment.

Fire, electrical shock or serious injury can result.

Turn off the power immediately if waterleaks into the equipment or the equipment is em- mitting smoke or fire.

Continued use of the equipment can cause fire or electrical shock.

Any repair work must be done by a licensed radio technician.

Improper repair work can cause electrical shock or fire.

RCAUTION

The transceiver and optional FM-3010 employ waterproof construction, which corresponds to JIS waterproof specification, Grade 7 (1 m/30 min.). However, once the transceiver or microphone has been dropped, wa- terproofing cannot be guaranteed due to the fact that the case may be cracked, or the waterproof seal damaged, etc.

AVOID the use of chemical agents such as benzine or al- cohol when cleaning, as they may damage the transceiver surfaces.

Distances at which radiation levels of 100 and 10 W/m2 exist are given in the table.

Distance to

Distance to

100 W/m2 point

10 W/m2 point

 

 

0.12 m

0.39 m

 

 

iii

Image 4
Contents Marine VHF Radiotelephone Foreword FM-3000Case of Emergency Do not disassemble or modify the equipment Do not open the equipmentAny repair work must be done by a licensed radio technician Only qualified personal should work in- side the equipment Standard SteerlingCompass TransceiverTable of Contents Setting Tag Channels Set Mode ProgrammingInstallation Panel DescriptionSystem Configulation ViiStandard supply Standard supply & OptionsOptions Controls Front PanelSQL control p HI/LO keyLO/DX IC SCR key 16 9 keyDistress key CH/WX DW U/I/C keyFunction Display Microphone Basic Operation Channel SelectionChannel Channel 9 Call channelPush once When Weather alert is OFF A. channels Or twice Weather channelsChange the channel group, if necessary Rotate Channel to select a channelPush HI/LO to select the output power, if necessary Receiving and TransmittingChannel Comments Call Channel ProgrammingPush Set mode Scrambler code item Optional Voice Scrambler OperationActivating the Scrambler Programming scrambler codesDualwatch/Tri-Watch DescriptionOperation Again Example Operating Tri-watch on INT ChannelScan Operation Scan TypesSetting Tag Channels Convinient Clearing setting all tagged channelsStarting a Scan Scan startsDSC Operation Mmsi Code ProgrammingDSC Individual ID Programming Address ID/Group IDSet the individual ID and ID name Deleting Address ID/Group IDRotate Channel to select the desired ID name for deleting Edit the digit of your latitude data by using Channel Edit the digit of your longitude data by using ChannelEdit the digit of the current UTC time by using CHAN- NEL Push DSC/ENT to set the time, and exit the DSC menuPosition/Time Indication Sentence formatteres ‘GGA,’ ‘GNS,’ ‘GLL’Distress Call Distress alert contains defaultSimple call Normal call Push Distress for 5 sec. to transmit the Distress call Transmitting Individual call Transmitting DSC CallsPush DSC/ENT to transmit the Individual call Transmitting Individual acknowledgement Indv ACK Transmitting Group call Push DSC/ENT to transmit the Group callTransmitting All Ships call Push DSC/ENT to transmit the All Ships callTransmitting Position Request call Push DSC/ENT to transmit the Position Request callTransmitting Position Report call Transmitting Position Report Reply call Transmitting Position Reply callPush DSC/ENT to transmit the Position Report call Receiving DSC Calls Receiving a Distress callReceiving a Distress acknowledgement Receiving an Individual callReceiving a Distress Relay call Receiving an All Ships callReceiving a Geographical Area call Receiving a Position Request call Receiving a Position Report callReceiving a Position Reply call Receiving a Position Report Reply callReceived Messages Distress messageRotate Channel to select Distress, push DSC/ENT Rotate Channel to scroll the messageOther messages Rotate Channel to select Other, push DSC/ENTDSC Set Mode Offset timeRotate Channel to select Offset time, push DSC/ENT Push DSC/ENT to program and to exit the DSC menuMmsi code check Rotate Channel to select Mmsi Check, push DSC/ENTCheck the 9-digit Mmsi DSC self ID code Push DSC/ENT to exit the DSC menuPush LO/DX IC SCR for 1 sec. to enter Intercom mode Other FunctionsIntercom Operation FM-3000 callerMicrophone Lock Function Display BacklightingSet Mode Programming Set ModeAuto ACK items are not selectable when using FM-3010 Set Mode Items Scan modeScan resume timer Weather alertThis item adjusts the contrast of the LCD in 8 steps DSC watchBeep tone Internal speakerScrambler code Attenuation levelAutomatic acknowledgement Connections and Maintenance Fuse ReplacementCleaning Antenna ConnectionsNmea in Red/NMEA OUT White Jacks Antenna ConnectorExternal Speaker Jack Using the supplied mounting bracket Mounting the TransceiverUsing the optional FM-3040 Attach the clamps on either side of the FM-3000Optional Unit Installation 145.0 5 23⁄32 103.0 110.0 4 11⁄32 165.0 6 1⁄2 Dimensions53.0 ⁄32 Unit mm Troubleshooting Problem Possible Cause Solution† Low power only Channel ListOperating Rules Radio license for boaters U.S.A. onlySpecifications SpecificationsGeneral TransmitterPTT Switch PTT pgs Panel DescriptionFront and side keys Channel UP/DOWN Keys Y/ZVOLUME/DIMMER KEY VOL DIM CHANNEL/DUALWATCH/TRI-WATCH KEY CH/WX DW U/I/CLO/DX IC SCR SQUELCH/MONITOR/LOCK KEY SQL Moni LTop keys Volume Indicator p Squelch Indicator pScan Indicator pgs 1DUAL/TRI Watch Indicator pgsCall channel 13.3 3 Weather channelsChannel group A. channelsPush H/L to select the output power, if necessary Turn power on Set outputPush Y/Z to select the desired channel Push Y/Z to adjust the backlight level Lock FunctionsActivating the Lock function Activating the All key lock functionMonitor Function RF Attenuator FunctionPush LO/DX to turn the RF Attenuator function on and OFF Push CH/WX DW U/I/C severalDualwatch/Tri-watch Operation Programming scramble codesPush Y/Z to select the desired channel LO/DX IC SCR to turnConvenient Clearing setting all tagged channels To cancel the tag channel setting, push Scan TAG for 1 secTo stop the scan, push Scan TAG Turn power OFF While pushing 16 9 , turn power on Entering Set modeBeep tone Beep Push SQL to move to forward then push Y/Z to se Intercom beep functionAvailable characters Accessories included with the FM-3010 Qty 13.17 FM-3010 supplied accessoriesConnection cable FM-3011 6 m 20 ft Installation Completed installation should look like thisMm 3⁄32˝ 165 mm 61⁄2 149 mm 57⁄8 R11 Mm 3⁄32