Furuno FM-3000 Only qualified personal should work in- side the equipment, Standard Steerling

Page 5

	For the installer
R WARNING	R WARNING

ELECTRICAL SHOCK HAZARD Do not open the equipment un- less totally familiar with electri- cal circuits and service manual.

Only qualified personal should work in- side the equipment.

Be sure that the power supply is compatible with the voltage rating of the equipment.

Connection of an incorrect power supply can cause ﬁre or equipment damage. The voltage rating of the equipment ap- pears on the label above the power connector.

Turn off the power at the switchboard before beginning the installation.

Fire or electrical shock can result if the power is left on.

DO NOT install the equipment where normal operation of the vessel may be hindered or where it could cause bodily injury.

DO NOT cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cut- ting, the equipment may be damaged.

RCAUTION

Ground the equipment to pre- vent electrical shock and mutual interference.

Observe the following compass safe dis- tances to prevent interference to a magnetic compass:

	Standard	Steerling
	compass	compass

Transceiver	0.95 m	0.65 m

iv

Image 5

Contents Marine VHF Radiotelephone FM-3000 ForewordCase of Emergency Any repair work must be done by a licensed radio technician Do not open the equipmentDo not disassemble or modify the equipment Standard Steerling Only qualified personal should work in- side the equipmentCompass TransceiverTable of Contents Set Mode Programming Setting Tag ChannelsInstallation Panel DescriptionVii System ConﬁgulationOptions Standard supply & OptionsStandard supply Front Panel ControlsSQL control p HI/LO key16 9 key LO/DX IC SCR keyDistress key CH/WX DW U/I/C keyFunction Display Microphone Channel Selection Basic OperationChannel Channel 9 Call channelWeather channels Push once When Weather alert is OFF A. channels Or twiceChange the channel group, if necessary Rotate Channel to select a channelReceiving and Transmitting Push HI/LO to select the output power, if necessaryPush Call Channel ProgrammingChannel Comments Optional Voice Scrambler Operation Set mode Scrambler code itemActivating the Scrambler Programming scrambler codesDescription Dualwatch/Tri-WatchOperation Again Example Operating Tri-watch on INT ChannelScan Types Scan OperationConvinient Clearing setting all tagged channels Setting Tag ChannelsStarting a Scan Scan startsMmsi Code Programming DSC OperationDSC Individual ID Programming Address ID/Group IDRotate Channel to select the desired ID name for deleting Deleting Address ID/Group IDSet the individual ID and ID name Edit the digit of your longitude data by using Channel Edit the digit of your latitude data by using ChannelEdit the digit of the current UTC time by using CHAN- NEL Push DSC/ENT to set the time, and exit the DSC menuSentence formatteres ‘GGA,’ ‘GNS,’ ‘GLL’ Position/Time IndicationSimple call Distress alert contains defaultDistress Call Normal call Push Distress for 5 sec. to transmit the Distress call Push DSC/ENT to transmit the Individual call Transmitting DSC CallsTransmitting Individual call Transmitting Individual acknowledgement Indv ACK Push DSC/ENT to transmit the Group call Transmitting Group callPush DSC/ENT to transmit the All Ships call Transmitting All Ships callPush DSC/ENT to transmit the Position Request call Transmitting Position Request callTransmitting Position Report call Push DSC/ENT to transmit the Position Report call Transmitting Position Reply callTransmitting Position Report Reply call Receiving a Distress call Receiving DSC CallsReceiving a Distress acknowledgement Receiving an Individual callReceiving a Geographical Area call Receiving an All Ships callReceiving a Distress Relay call Receiving a Position Report call Receiving a Position Request callReceiving a Position Reply call Receiving a Position Report Reply callDistress message Received MessagesRotate Channel to select Distress, push DSC/ENT Rotate Channel to scroll the messageRotate Channel to select Other, push DSC/ENT Other messagesOffset time DSC Set ModeRotate Channel to select Offset time, push DSC/ENT Push DSC/ENT to program and to exit the DSC menuRotate Channel to select Mmsi Check, push DSC/ENT Mmsi code checkCheck the 9-digit Mmsi DSC self ID code Push DSC/ENT to exit the DSC menuOther Functions Push LO/DX IC SCR for 1 sec. to enter Intercom modeIntercom Operation FM-3000 callerDisplay Backlighting Microphone Lock FunctionAuto ACK items are not selectable when using FM-3010 Set ModeSet Mode Programming Scan mode Set Mode ItemsScan resume timer Weather alertDSC watch This item adjusts the contrast of the LCD in 8 stepsBeep tone Internal speakerAutomatic acknowledgement Attenuation levelScrambler code Fuse Replacement Connections and MaintenanceCleaning Antenna ConnectionsExternal Speaker Jack Antenna ConnectorNmea in Red/NMEA OUT White Jacks Mounting the Transceiver Using the supplied mounting bracketAttach the clamps on either side of the FM-3000 Using the optional FM-3040Optional Unit Installation 53.0 ⁄32 Unit mm Dimensions145.0 5 23⁄32 103.0 110.0 4 11⁄32 165.0 6 1⁄2 Problem Possible Cause Solution TroubleshootingChannel List † Low power onlyRadio license for boaters U.S.A. only Operating RulesSpeciﬁcations SpeciﬁcationsGeneral TransmitterPanel Description PTT Switch PTT pgsFront and side keys Channel UP/DOWN Keys Y/ZCHANNEL/DUALWATCH/TRI-WATCH KEY CH/WX DW U/I/C VOLUME/DIMMER KEY VOL DIMLO/DX IC SCR SQUELCH/MONITOR/LOCK KEY SQL Moni LTop keys Squelch Indicator p Volume Indicator pScan Indicator pgs 1DUAL/TRI Watch Indicator pgs13.3 3 Weather channels Call channelChannel group A. channelsPush Y/Z to select the desired channel Turn power on Set outputPush H/L to select the output power, if necessary Lock Functions Push Y/Z to adjust the backlight levelActivating the Lock function Activating the All key lock functionRF Attenuator Function Monitor FunctionPush LO/DX to turn the RF Attenuator function on and OFF Push CH/WX DW U/I/C severalProgramming scramble codes Dualwatch/Tri-watch OperationPush Y/Z to select the desired channel LO/DX IC SCR to turnTo stop the scan, push Scan TAG To cancel the tag channel setting, push Scan TAG for 1 secConvenient Clearing setting all tagged channels Beep tone Beep Entering Set modeTurn power OFF While pushing 16 9 , turn power on Available characters Intercom beep functionPush SQL to move to forward then push Y/Z to se Connection cable FM-3011 6 m 20 ft 13.17 FM-3010 supplied accessoriesAccessories included with the FM-3010 Qty Completed installation should look like this InstallationMm 3⁄32˝ R11 Mm 3⁄32 165 mm 61⁄2 149 mm 57⁄8