Furuno FM-3000 manual Optional Unit Installation

Page 54

8.Connections and Maintenance

8.6 Optional Unit Installation

RCAUTION

DISCONNECT the DC power cable from the trans- ceiver before performing any work on the trans- ceiver. Otherwise, there is danger of electric shock and/or equipment damage.

Follow the case opening procedure shown here when you want to install an optional unit.

qRemove the 6 screws as shown below and open the trans- ceiver.

wRemove the 4 screws from the shielding plate, then lift up the shielding plate.

ePlug an optional unit (FM-3030) to J3 on the MAIN unit as shown below.

Optional unit

rReturn the shielding plate and assemble the units to their original positions.

RCAUTION

1.When re-assembling the case and tightening the screws, you must keep the specified torque (0.7±0.1 N.m). Otherwise the transceiver may be damaged (torque too high) or lose waterproof efﬁ- ciency (torque too low).

2.When uninstalling the optional unit, remove it ver- tically. Wiggling the unit from side to side may damage the optional unit's connector.

45

Image 54

Contents Marine VHF Radiotelephone Foreword FM-3000Case of Emergency Do not open the equipment Do not disassemble or modify the equipmentAny repair work must be done by a licensed radio technician Compass Only qualified personal should work in- side the equipmentStandard Steerling TransceiverTable of Contents Installation Setting Tag ChannelsSet Mode Programming Panel DescriptionSystem Conﬁgulation ViiStandard supply & Options Standard supplyOptions SQL control p ControlsFront Panel HI/LO keyDistress key LO/DX IC SCR key16 9 key CH/WX DW U/I/C keyFunction Display Microphone Channel Basic OperationChannel Selection Channel 9 Call channelChange the channel group, if necessary Push once When Weather alert is OFF A. channels Or twiceWeather channels Rotate Channel to select a channelPush HI/LO to select the output power, if necessary Receiving and TransmittingCall Channel Programming Channel CommentsPush Activating the Scrambler Set mode Scrambler code itemOptional Voice Scrambler Operation Programming scrambler codesOperation Dualwatch/Tri-WatchDescription Again Example Operating Tri-watch on INT ChannelScan Operation Scan TypesStarting a Scan Setting Tag ChannelsConvinient Clearing setting all tagged channels Scan startsDSC Individual ID DSC OperationMmsi Code Programming Programming Address ID/Group IDDeleting Address ID/Group ID Set the individual ID and ID nameRotate Channel to select the desired ID name for deleting Edit the digit of the current UTC time by using CHAN- NEL Edit the digit of your latitude data by using ChannelEdit the digit of your longitude data by using Channel Push DSC/ENT to set the time, and exit the DSC menuPosition/Time Indication Sentence formatteres ‘GGA,’ ‘GNS,’ ‘GLL’Distress alert contains default Distress CallSimple call Normal call Push Distress for 5 sec. to transmit the Distress call Transmitting DSC Calls Transmitting Individual callPush DSC/ENT to transmit the Individual call Transmitting Individual acknowledgement Indv ACK Transmitting Group call Push DSC/ENT to transmit the Group callTransmitting All Ships call Push DSC/ENT to transmit the All Ships callTransmitting Position Request call Push DSC/ENT to transmit the Position Request callTransmitting Position Report call Transmitting Position Reply call Transmitting Position Report Reply callPush DSC/ENT to transmit the Position Report call Receiving a Distress acknowledgement Receiving DSC CallsReceiving a Distress call Receiving an Individual callReceiving an All Ships call Receiving a Distress Relay callReceiving a Geographical Area call Receiving a Position Reply call Receiving a Position Request callReceiving a Position Report call Receiving a Position Report Reply callRotate Channel to select Distress, push DSC/ENT Received MessagesDistress message Rotate Channel to scroll the messageOther messages Rotate Channel to select Other, push DSC/ENTRotate Channel to select Offset time, push DSC/ENT DSC Set ModeOffset time Push DSC/ENT to program and to exit the DSC menuCheck the 9-digit Mmsi DSC self ID code Mmsi code checkRotate Channel to select Mmsi Check, push DSC/ENT Push DSC/ENT to exit the DSC menuIntercom Operation Push LO/DX IC SCR for 1 sec. to enter Intercom modeOther Functions FM-3000 callerMicrophone Lock Function Display BacklightingSet Mode Set Mode ProgrammingAuto ACK items are not selectable when using FM-3010 Scan resume timer Set Mode ItemsScan mode Weather alertBeep tone This item adjusts the contrast of the LCD in 8 stepsDSC watch Internal speakerAttenuation level Scrambler codeAutomatic acknowledgement Cleaning Connections and MaintenanceFuse Replacement Antenna ConnectionsAntenna Connector Nmea in Red/NMEA OUT White JacksExternal Speaker Jack Using the supplied mounting bracket Mounting the TransceiverUsing the optional FM-3040 Attach the clamps on either side of the FM-3000Optional Unit Installation Dimensions 145.0 5 23⁄32 103.0 110.0 4 11⁄32 165.0 6 1⁄253.0 ⁄32 Unit mm Troubleshooting Problem Possible Cause Solution† Low power only Channel ListOperating Rules Radio license for boaters U.S.A. onlyGeneral SpeciﬁcationsSpeciﬁcations TransmitterFront and side keys PTT Switch PTT pgsPanel Description Channel UP/DOWN Keys Y/ZLO/DX IC SCR VOLUME/DIMMER KEY VOL DIMCHANNEL/DUALWATCH/TRI-WATCH KEY CH/WX DW U/I/C SQUELCH/MONITOR/LOCK KEY SQL Moni LTop keys Scan Indicator pgs Volume Indicator pSquelch Indicator p 1DUAL/TRI Watch Indicator pgsChannel group Call channel13.3 3 Weather channels A. channelsTurn power on Set output Push H/L to select the output power, if necessaryPush Y/Z to select the desired channel Activating the Lock function Push Y/Z to adjust the backlight levelLock Functions Activating the All key lock functionPush LO/DX to turn the RF Attenuator function on and OFF Monitor FunctionRF Attenuator Function Push CH/WX DW U/I/C severalPush Y/Z to select the desired channel Dualwatch/Tri-watch OperationProgramming scramble codes LO/DX IC SCR to turnTo cancel the tag channel setting, push Scan TAG for 1 sec Convenient Clearing setting all tagged channelsTo stop the scan, push Scan TAG Entering Set mode Turn power OFF While pushing 16 9 , turn power onBeep tone Beep Intercom beep function Push SQL to move to forward then push Y/Z to seAvailable characters 13.17 FM-3010 supplied accessories Accessories included with the FM-3010 QtyConnection cable FM-3011 6 m 20 ft Installation Completed installation should look like thisMm 3⁄32˝ 165 mm 61⁄2 149 mm 57⁄8 R11 Mm 3⁄32