Aiphone IS-SOFT Calling another station direct voice call, Click To start calling talking

Page 25

Calling another station (direct voice call)

Follow the steps below to call a desired door station, room sub station or master station in your site, or remote site.

1 Search for and select the station or remote site you want to call (so that it is highlighted) in one of the search methods. (→P. 21-24)

*If you call (the pilot station in) a remote site by searching for it from [REMOTE SITE] of SEARCH LIST, select the target site, and then select [CALL] (so that it is highlighted). (→P. 23)

Refer to the on-screen instructions:

Be sure to make operations by checking the information on the upper part of the list area. The next operations you can perform are displayed.

e.g.)

[ ] TALK … You can start talking by clicking

.

*If you will not set the priority, it is set to “Normal”.

[] MONI … You can start monitoring by clicking . [ ] PR (or PRIORITY)

………You can proceed to the priority setting mode by clicking .

2 To set the priority, click , and then click

to

select the target priority (so that it is highlighted).

*If you will not set the priority, skip this step and click

. You can start calling (talking) with “Normal” priority.

3 Click

or

to start calling (talking).

or

When a tone rings, your voice is heard at the target station and you can also hear sounds at the target station. (Direct voice call)

The receiver can answer the call without pressing any button or lifting the handset. (Talk back)

*If the target station is a (PC) master station, the response of it differs from the PRIVACY mode setting on the target station. (See the table below.)

PRIVACY mode

 

setting on the target

Response

master station

 

 

Your voice is heard at the target

OFF

station and you can also hear sounds

 

at the target station.

 

 

 

Communication is enabled when

1

the receiver makes an answering

operation. Otherwise you can hear no

 

 

sound from the target station.

 

 

 

When the target station receives your

 

call, a tone notifies you that the target

 

station is in the “Privacy 2” mode.

 

Communication is enabled when

 

the receiver makes an answering

2

operation. Otherwise you can hear no

 

sound from the target station.

 

* You can adjust the volume of call

 

tone by using the speaker volume

 

adjusting slider in the volume

 

control window.

 

 

4 Click to finish communicating.

GETTING STARTED USING THE PC MASTER STATIONAPPENDIX

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents IS-SOFT Contents Playing recorded image And/or sound Deleting a recorded file Connecting a headset or handset to the PCIntroduction PrecautionsMain window Part Names and Their FunctionsIcons Status when the icon appears How to select items in the list areaStatus display icons Minimize button Audio transmit level indicatorClose button Dial keys →PStation Select tab →P -31 Start Date selection tab and calendarPrior file button Stop buttonCommunication Outline of OperationsYou cannot monitor or scan-monitor a remote site Door release Call tone rings, and the corresponding display appears Receiving a callCommunication in the press-to-talk mode Communication in the hands-free modeWhen called in from a sub station About the priority Priority Setting ActionPan & Tilt Switching Zoom/WideWide Zoom Left Right DownClick When the image is difficult to see Adjusting imagesTo restore the image before adjustment DayNightCall transferring Communication transferringReceive a call and communicate with it. →P To communicate with the caller While receiving a callStandby mode Basic procedure for selecting the search itemsSearch items Placed calls →PChime Zone →P Search ListTo select two or more stations and/or zones from the list Searching for a station, zone or remote site from the listSelect Stations by Type from the Search LIST. →P Start paging by following the procedure for pagingSelect Paging Zone from the Search List Click to select the target zone so that it is highlightedClick to select the target site so that it is highlighted Select Remote Site from the Search ListPage Click To start calling talking Calling another station direct voice callClick to finish communicating Monitoring Viewing video images at the target stationScan-monitoring To shift to scan-monitoringClick or when Chime is displayed When you have finished paging, clickOr lifting the handset Or pressing the external call button*1OFF RecordingAuto recording How to perform manual recording Snapshot recordingVideo recording Playing recorded image and/or sound PlayClick On the Main window Play operation list When play has finishedSpecifications Technical Precautions Available Character ListWindows XP Home/Professional SP3 32bit
Top Page Image Contents