Philips DBS-EX23-530 manual MDF card installation

Page 35

Installation

Installation Procedures

5.Install the MDF (main distribution frame) card in the top of the cabinet as shown in Figure 2-5.

Figure 2-5. MDF card installation

Revised April 2000

DBS-EX23-530

2-17

Image 35

Contents For CPC-EX Version IsdnPage Contents DBS-EX23-530 Revised Programming ReferenceList of Figures List of Tables Chapter Title Purpose About This ManualOverview Related DocumentsViii DBS-EX23-530 Revised April Topic Introduction to the Isdn InterfaceDBS-EX23-530 Revised April Introduction to the Isdn Interface Overview OverviewDescription of the Isdn Interface Framing OptionsTypical Information for CO Comments Examples Pre-Installation RequirementsOrdering Isdn Information Needed from CO Comments / ExamplesLpic Typical Information for CO Site Information Information Needed from CO Site InformationESF Span Item Master Cabinet Span Slave Cabinet SpanDBS Equipment What You Must PurchaseCSU Equipment Page Installation DBS-EX22-530 Revised April Maximums Installation GuidelinesGuidelines Hardware RequirementsGuidelines Installation Trunk Assignments for Single-Cabinet Systems Trunk Assignments for Double-Cabinet Systems Trunk Master Cabinet Slave Cabinet Number System Size Master SlaveTrunk Master Cabinet Slave Cabinet Number Trunk Master Cabinet Slave Cabinet Number Trunk Master Cabinet Slave Cabinet Number Trunk Master Cabinet Slave Cabinet Number If you’re installing Use this procedure Installation ProceduresInstalling the CSU Installation ProceduresParameter System Configuration Installation Installation ProceduresInstalling an Isdn in a Single Cabinet Attach the Sync Unit to the CPC-EX card Sync Unit installation MDF card installation To 150 ft 150-450 ft 450-655 ft Distance from the DBS to the CSURJ48 Pin Designations Pins DesignationIsdn cabinet connections, single-cabinet installation Installation Installation Procedures Installation Procedures Installation Installation Procedures Slave Cabinet Quick-Start Programming DBS-EX23-530 Revised April Quick-Start Programming Before You Begin Before You BeginProgramming Initial Isdn Options Quick-Start Programming DBS-EX22-530 Issued 10/23/98Programming Initial Isdn Options Minimum Programming=Free run internal clocking Quick-Start Programming Programming Initial Isdn Options= Loop start DisablePublic NoneDetermine Type and Plan Send as isFF1 9# 4# 5# 5# 3# 0-2# NSF =Off Multiple did Programming=DID data on display CO Type 0 4ESS Typical Central Office ConfigurationsProgramming Reference DBS-EX23-530 Revised April =T1 Isdn System SettingsProgramming Reference Isdn System Settings System SizeIsdn System SettingsProgramming Reference Clock Settings=None Isdn System Settings Programming Reference Programming Reference System-Wide Timers System-Wide Timers=4 sec System-Wide Timers Programming Reference15=Infinite =30 sec System-Wide Timers Programming Reference Programming Reference System-Wide Timers Digital Pad Settings Programming Reference Digital Pad SettingsSLT Isdn #2 Programming Reference Digital Pad SettingsDigital Pad SettingsProgramming Reference Extension Port SettingsProgramming ReferenceDigital Pad Settings Trunk Port SettingsMaster and Slave Settings Programming Reference Master and Slave SettingsTrunk Configuration Trunk SignalingAlarm Description Notification Alarm SettingsAlarm Descriptions Programming Reference Alarm SettingsParameter Address Function Alarm Settings Programming ReferenceSlip Alarms =Yes Alarm Transmission Options=10 ms Alarm TimersProgramming ReferenceAlarm Settings Error Counters for FF Alarm Keys Programming Reference Alarm Settings Alarm Settings Programming Reference =Off Alarm relay does not close Alarm Relay ControlsAlarm Settings Programming Reference =Auto =Do not reset Trunk SettingsTrunk Settings Programming Reference Public network Programming Reference Trunk SettingsNone DisableSend as is with leading Send as is withTrunk Settings Programming Reference =Off Extension Settings Programming Reference Extension SettingsAlarm Master Isdn Slave Isdn FF Key SettingsProgramming Reference FF Key Settings Special Isdn Function Codes Programming Reference Special Isdn Function CodesProgramming Reference Special Isdn Function Codes Yellow New Features Appendix a CPC-EX 2.3 UpdatesSoftware Corrections Programming Port Voice Mail Support via APISmall LCD Soft Key Support via API Off-Hook Voice Announce Ohva via APICall Record Ohva via API UNA Transfer Special FeaturesUNA Call Reversion Setting ValueForwarding to UNA for CO Held Call DBS-2.3-400 DBS Manual Revised April A-9 All Ring Group FF1 6# 3# NNNN# Private PasswordON/OFF #93 Terminal Programming Through a Direct ConnectionTerminal Programming Through Disa Command Description Additional RAI Access MethodTerminal Programming Through Additional RAI Access Method Terminal Programming CommandsDBS-2.3-400 DBS Manual Revised April A-15 Name Key Sequence Isdn Upgrade ProcedureIsdn Programming Flexibility Master Cabinet Set-Up Determine Type and Plan DMS100Send as is DMS-100 Slave Cabinet Set-UpLucent AT&T 5ESS Typical Central Office Configurations Lucent AT&T 4ESSTypical Info for CO Comments examples Nortel NT DMS100Info Needed from CO Comments examples Will exceed the total number of B channels DBS-2.3-400 DBS Manual Revised April A-23 Affected Items Feature ChangesFF1 2# 2# 7# System Speed Bins 257- 500 Unavailable Revised April DBS-EX23-530 Index-i IndexIndex-ii DBS-EX23-530 Revised April Sync cable 2-18, 2-21, 2-23 Sync loss alarm