Panasonic KX-TG8301NZ operating instructions Error messages

Page 39

Useful Information

Error messages

If the unit detects a problem, one of the following messages is shown on the display.

Display message	Cause/solution
Check Tel Line	L The supplied telephone line cord has not been
	connected yet or not connected properly. Check the
	connections (page 11).
Failed	L Phonebook copy failed (page 21). Confirm the other
	handset (the receiver) is in standby mode and try
	again.
Incomplete	L The receiver’s phonebook memory is full. Erase the
	unnecessary phonebook entries from the other
	handset (the receiver) and try again.
Memory Full	L The phonebook memory is full. Erase unnecessary
	entries (page 20).
	L The bar call list memory is full. Erase unnecessary
	entries (page 28).
	L The maximum number of base units (4) is already
	registered to the handset. Cancel unused base unit
	registrations from the handset (page 30).
No link to base.	L The handset has lost communication with the base
Reconnect AC	unit. Move closer to the base unit and try again.
adaptor.	L Unplug the base unit’s AC adaptor to reset the unit.
	Reconnect the adaptor and try again.
	L The handset’s registration may have been cancelled.
	Re-register the handset (page 29).
Use rechargeable	L A wrong type of batteries such as Alkaline or
battery.	Manganese was inserted. Use only the rechargeable
	Ni-MH batteries noted on page 3, 12.
You must first	L You must subscribe to a Caller ID service. Once you
subscribe to	receive caller information after subscribing to a Caller
Caller ID.	ID service, this message will not be displayed.

39

Image 39

Contents Model No. KX-TG8301NZ Preparation Caller ID ServiceVoice Mail Service IntroductionProduct information Accessory informationSupplied accessories Additional/replacement accessoriesExpanding your phone system For your safety Battery General noticesRechargeable Ni-MH batteries AAA R03 size Base unit location/avoiding noise Important safety instructionsFor best performance Important noticeIntroduction Charge contacts B x Locator ControlsBase unit HandsetSoft keys Using the joystickTo adjust the receiver or speaker DisplayConnections Battery installation and replacement During a power failureIf you subscribe to a DSL/ADSL service Battery level Battery icon Battery chargeDisplay language Screen saver modeTurning the power on/off Setting up the unit before useDate and time Time Settings Set Date & TimeBelt clip Headset optionalMaking calls Recall/flash Useful features during a callAnswering calls MuteCall privacy Key lockHandset voice enhancer Call shareFinding and calling a phonebook entry Handset phonebookAdding entries CategoriesOne Touch Dial Editing entriesErasing entries One touch dialCopying all entries Copying phonebook entriesChain dial Copying an entryProgramming by scrolling through the display menus Programmable settingsRingtone*2, *3 Night Mode Start/End On/Off Ring Delay 60 sec Select CategoryProgramming Programming Once Special instructions for programmable settingsMemo alarm Time adjustment Caller ID subscribers onlyNight mode Time AdjustmentRinger Setup iM Setting call restriction Selecting area codes to be deleted automaticallyChanging the base unit PIN Personal Identification Number Add Bar List iM Registering a unitIncoming call barring Caller ID subscribers only Operating additional unitsDeregistration Registering a handset to a base unitCancelling a base unit Setting the repeater modeIncreasing the range of the base unit Missed calls Using Caller ID serviceCaller ID features Using toll services from Telecom or another companyEditing a caller’s phone number before calling back Category settings for phonebookCaller list Viewing the caller list and calling backAdd Phonebook Erasing caller informationStoring caller information to the phonebook Edit and CallVoice mail service Intercom Making an intercom callAnswering an intercom call Base unit Press Handset Press ih Handset locatorAnswering a transferred call Press C to answer Base unit PressCharacter entry modes Characters available in each character entry modeWhen the unit displays the character entry screen Character entryExtended 1 character table N Extended 2 character table OCyrillic character table P Error messages General use Problem Cause/solution TroubleshootingProblem Cause/solution Programmable settings Problem Cause/solutionBattery recharge Problem Cause/solution Making/answering calls, intercom Problem Cause/solution Caller ID Problem Cause/solution Liquid damage Problem Cause/solution Specifications Index Page Copyright PNQX1195ZA CC0608DC0For your future reference Customer Support Centre Tel. No Sales Department