Panasonic KX-T2378JXW operating instructions Display

Page 6

PQQX13204YA-02 01.11.28 8:34 AM y [ W 6

Display

(This display shows all of the possible configurations.)

: In the standby mode, the display shows the current time. (Ex. 12:00AM)

: During a conversation, the call duration is displayed. (Ex. 2 hours, 14 minutes, 30 seconds)

: (FLASH) was pressed.

: (PAUSE) was pressed while storing phone numbers.

: ($) was pressed while dialing.

: (#) was pressed while dialing.

: (AUTO/LOWER) was pressed (p. 20, 23).

: (MUTE) was pressed during a conversation (p. 26).

: The unit is in the clock setting mode (p. 12).

: The unit is in the programming mode (p. 10).

: The dial lock mode is set. To cancel the mode, see page 28.

: This display flashes, when the battery power is low. To replace the batteries, see page 32.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents
Model No. KX-T2378JXW For your future reference Accessories includedBefore Initial Use Serial No Date of purchaseContents Location of Controls Indicator p , 17Volume Buttons p MIC Microphone p , 17 Mute Button p Hold Button pOne-Touch Auto Dial Buttons p Tone Button p Display p Button pPause Button p Redial Button p Flash Button p Display Connecting the Handset SettingsInstalling the Batteries Press down in the direction Arrow and open the coverTo connect two single-line telephone jacks Connecting the Telephone Line CordTo connect a two-line telephone jack Connect the telephone line cords to the unit as followsConnecting a Communication Device If you use the unit only as a single-line telephoneMake sure that a call is not put on hold Press Program to store the settingProgramming Summary of Preparations Press MuteSelecting the Dialing Mode To select Pulse, press2 To select Tone, press1Time Adjustment You can select AM/PM or 24-hour clock by programmingPress Setting the LCD ContrastSelecting the Ringer Volume Press 1 toWall Mounting Wall TemplateLocks, so the tab holds the handset Using the handset Using the speakerphoneMaking Calls To release the hold To redial the last number dialedTo put a call on hold Automatic RedialWhat the line indicator means Answering CallsUsing the Other Line During a Conversation Ex If you are using LINE1Ex If you are using Line Conference CallDuring a conference call Enter a phone number, up to 22 digits Speed DialerStoring Phone Numbers in Memory Press a memory station number 0 toDialing a Stored Number To erase a stored numberOne-Touch Dialer To store in an Upper memory locationPress one of the one-touch auto dial buttons To store in a Lower memory location If the phone number is in an UpperMemory location, press the one-touch From an Upper memory location From a Lower memory locationMemory card How to Use the Pause Button Special FeaturesFor Call Waiting Service Users Temporary Tone DialingSelecting the flash time Muting Your ConversationFlash Button Press Mute while talkingEnter the current PIN code Setting the PIN CodeEnter a new PIN code using a 4-digit Ex is enteredTo set the dial lock To cancel the dial lockDial Lock Enter the PIN code pCall Restriction To set the call restrictionEnter the PIN code p Ex. Your PIN code is Using the Optional Headset To cancel the call restrictionConnecting the Optional Headset to the Unit Make sure to install the batteries To adjust the headset receiver volume 4 levelsMaking/Answering Calls Battery Replacement Battery PrecautionsProblem Remedy Before Requesting HelpProblemRemedy Before Requesting HelpSafety Instructions Installations Environment62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan PQQX13204YA F1001-1111D
Related manuals
Manual 36 pages 8.71 Kb