Roland RS 232C manual Control Commands, = PAPhrAse, = PE PausE

Page 12

r

3) Setting commands

These commands are used to set AR-3000 parameters from the external device.

4) Request commands

This command causes the AR-3000 to output the status of its current settings. When a Request command is transmitted to the AR-3000, the AR-3000 will transmit the requested contents as the Setting output command. In this case, an ACK will not be returned. However for the AC and AQ commands, an ACK will be output. If the command was not correct, an ER command will be returned.

5) Reply commands

Reply commands are necessary for communication control, for example to notify that a command was received correctly.

4.2 Details of Commands Sent from the External Device (Computer) to the AR-3000

Commands compatible with the AR-2000 are marked as shown below (relevant symbol appears before name).

=Commands for the AR-2000/AR-3000 (those common to both the AR-2000 and AR-3000) > Commands for the AR-3000 (commands newly added with the AR-3000)

< Commands for the AR-2000 (for the AR-2000; includes items that cannot be used with the AR-3000)

4.2.1 Control Commands

Playback Commands

= PA(PhrAse)

Function:	Specifying the playback phrase
Syntax:	stxPA: **, , ....., ** ;
	a	a	a

a Phrase number

Example) PA:A1,A3,B5;

Specify A0001 and A0003 and B0005 as the playback phrases.

The specified phrases are consecutively played back from the left.

Note: A maximum of 100 phrases can be specified in one line.

Be sure that the phrase numbers are registered (i.e., for which data exists).

= PE (PausE)

Function: Playback pause / Restart playback

Syntax:	stxPE;
Note:	When this command is sent during phrase playback, the AR-3000 stops playback and
	enters the paused state. Sending the PE command again releases the pause, and
	playback resumes from where it was paused. When operation is paused with the PE
	command, the AR-3000 outputs the elapsed time from the start of the phrase to the
	point where paused. (Refer to AE command 4 . 4 . 1 )

Caution:The command is not compatible with the Dual Mono.

Phrases other than audio phrases cannot be specified.

AR-3000 RS-232C Reference -7

Image 12

Contents RS-232C Reference AR-3000 RS-232C Reference versionContents SetupOverview of Commands Details of each CommandSetting Commands ACK Appendix If You Have Been Using the AR-2000 Connector and CableAbout the RS-232C Interface HandshakingSetup Procedure Computer SettingsAR-3000 Settings Connections with the ComputerBaud Rate Settings Command StructureCommunication Protocol Stx + DM command Command Format PrecautionsAbout Input Parameters About Output ParametersDetails of each Command Control Commands = PAPhrAse= PE PausE Phrases other than audio phrases cannot be specifiedIf Dual Mono Mode is on = PL PLay= RL Relative time pLay Syntax stxRL * , **H**M**S**F stxRL * , **H**M**SRecording Commands StxAEExample stxAE2001,3,1,8,59,0,0,1,0 = RE REc start= RM Rec Mode Syntax stxRM **** , * , * , * , * , * , * a b c d e f gExample RMA1,3,2,1,0,1,1 Editing Commands = DM Delete Mode= CD Card Delete Function Delete Card Syntax stxDM = CP Card coPy= LS phrase Lock Switch LW phrase Lock sWitch for AR-3000= FM ForMat = SP Setting coPy Function System copy Syntax stxDM = PC Phrase Copy Function Copy phrase Syntax stxDM= PD Phrase Delete = PI Phrase sIlencerStxPV ****,**H**M**S**F*S StxPMTS Time Stretch for AR-3000 StxTSStxDM StxRT Syntax3 Mono1 , Mono2 to Stereo stxDM StxRTSetting Commands Pattern Phrase SettingsExample stxCV0,ABCDEFGH Syntax stxPU **** , * , **** , **S* , .... , **** , **SSong Phrase number Phrase number to be played back Phrase Settings Example SUA001,ABCDEFGHIJK,100,10S5,1,5M0S,1,5M10S,120,0PO Phrase control Out set up for AR-3000 PP phrase Playback Point set up for AR-3000Syntax stxPO **** , *,**M**S Syntax stxPP **** , **H**M**S**F*S, **H**M**S**F*SMPphrase Midi temPo set up for AR-3000 Syntax stxMPSyntax stxTT Midi Settings = MS Midi Set up Function Midi settingsSyntax stxMS MM MMc set up for AR-3000 MT MTc set up for AR-3000Function MTC settings Syntax stxMT= NM Note Map Syntax stxNM= BR Baud Rate = DC Display ContrastDL Direct pLay for AR-3000 Function Direct Playback setting StxDPExample DP0,A1,,A3,A4,,A16 Syntax stxDLSM SysteM for AR-2000Function System settings Syntax stxSM AR-3000 RS-232C Reference Syntax stxEQ StxBORequest Commands 2Q pattern phrase reQuest for AR-20003Q pattern phrase reQuest for AR-3000 GQ sonG phrase reQuest for AR-3000= AQ All reQuest = CQ Card reQuest= DQ Direct play reQuest = LQ dispLay contrast reQuest = MQ Memory reQuest= NQ Note map reQuest Syntax stxNQ * aYQ sYstem reQuest for AR-3000 Syntax stxYQ= UQ coUnt play reQuest Syntax stxUQ= VR VeRsion Reply Commands = ER ERror= Xon 11H/Xoff 13H = CS Card SetCard ID Created automatically Reserved SU phrase Set Up for AR-2000 Function Phrase setting output S**F*S, **H**M**S**F*S,*,*, **H**M**S**F**S, **H**M**S**F**S Endless Syntax stxME Master Slave Sync Source Internal = CE Count play sEt up Syntax stxAC= CR Card Remain Syntax stxCR= DP Direct Play SY SYstem for AR-3000 Function System setting output = TI Time stamp Info Syntax stxTISyntax stxVR AR-3000 RS-232C Reference = AE Auto inc rEc start Syntax stxAE S**** aSyntax stxER * a = Xon 11H / Xoff 13H AR-3000 Commands List 1 AR-2000 Compatible Commands List # Control Commands # Playback CommandsEditing Commands # Setting Commands # Card Settings# Reply Commands # Commands sent from the AR-3000 to the external device# Setting Output Commands Reply Commands# Editing Commands # Card Editing # Setting Commands # Phrase Settings# Midi Settings # System Settings# Setting Output Commands # Phrase Settings Characters That Can Be Used in Phrase Names and Card NamesSample Algorithms Playing Back a PhraseRecording Nomal Recording Recording Time-Stamped Recording What is the Phrase Output Counter? Deleting a Phrase