Roland RS 232C manual = AE Auto inc rEc start, Syntax stxAE S**** a, Syntax stxER * a

Page 50

r

Note: When operation is paused with the PE command, the AR-3000 outputs the elapsed time from the start of the phrase to the point where paused.

The number of digits for **F (frame) increases according to the value of MTC type

= AE ( Auto inc rEc start )

Function: Output the total number of phrases recorded on the card

Syntax: stxAE: S**** ; a

a the total number of phrases recorded on the card

Note: This is output when AR receives an AE command.

4.4.2Reply Commands

=ER (ERror)

Function: Replies when an error has occurred.

Syntax: stxER: * ; a

aError number

0Syntax error

This error occurs when correct reception was not possible, such as when the syntax of the command was incorrect or inappropriate.

1The specified phrase does not exist, or the phrase number is incorrect. This error will also be output if a phrase number is specified for a card which is not inserted.

2Busy error.

The AR-3000 is currently recording or playing back. When the AR-3000 is recording or playing back, it will process only the following commands.

	Control commands	Request commands
During	PA , ST	AC
Recording

During Play	PA , ST , PE	AC

During Play	PA , ST , PE , RL	AC
Pause

3An editing command was received when the AR-3000 was not in Delete mode.

4This error occurs if a setting/delete/record command is transmitted while the write protect switch of the card is ON.

5This error occurs when the total number of phrases specified by the PA, PU, or CE commands exceeds the maximum value (100), or when the specified parameter value is outside of the limit of the maximum value.

6This error occurs when the characters being set for a phrase name or card name exceed the maximum value.

7This error occurs when characters other than numerals (0 - 9) are used to specify an integer.

8This error occurs when you attempt to specify a previously recorded phrase as a pattern phrase.

9This error occurs when you attempt to record or copy a phrase on an already

recorded phrase.

10 There is no remaining card capacity.

20 The command could not be executed for some other reason.

AR-3000 RS-232C Reference -45

Image 50

Contents RS-232C Reference AR-3000 RS-232C Reference versionOverview of Commands ContentsSetup Details of each CommandSetting Commands ACK Appendix About the RS-232C Interface If You Have Been Using the AR-2000Connector and Cable HandshakingAR-3000 Settings Setup ProcedureComputer Settings Connections with the ComputerCommunication Protocol Baud Rate SettingsCommand Structure Stx + DM command About Input Parameters Command FormatPrecautions About Output ParametersDetails of each Command = PE PausE Control Commands= PAPhrAse Phrases other than audio phrases cannot be specified= RL Relative time pLay If Dual Mono Mode is on= PL PLay Syntax stxRL * , **H**M**S**F stxRL * , **H**M**SExample stxAE2001,3,1,8,59,0,0,1,0 Recording CommandsStxAE = RE REc startExample RMA1,3,2,1,0,1,1 = RM Rec ModeSyntax stxRM **** , * , * , * , * , * , * a b c d e f g = CD Card Delete Function Delete Card Syntax stxDM Editing Commands= DM Delete Mode = CP Card coPy= FM ForMat = LS phrase Lock SwitchLW phrase Lock sWitch for AR-3000 = PD Phrase Delete = SP Setting coPy Function System copy Syntax stxDM= PC Phrase Copy Function Copy phrase Syntax stxDM = PI Phrase sIlencerTS Time Stretch for AR-3000 StxPV ****,**H**M**S**F*SStxPM StxTSStxDM StxRT Syntax3 Mono1 , Mono2 to Stereo stxDM StxRTExample stxCV0,ABCDEFGH Setting CommandsPattern Phrase Settings Syntax stxPU **** , * , **** , **S* , .... , **** , **SSong Phrase number Phrase number to be played back Phrase Settings Example SUA001,ABCDEFGHIJK,100,10S5,1,5M0S,1,5M10S,120,0Syntax stxPO **** , *,**M**S PO Phrase control Out set up for AR-3000PP phrase Playback Point set up for AR-3000 Syntax stxPP **** , **H**M**S**F*S, **H**M**S**F*SSyntax stxTT MPphrase Midi temPo set up for AR-3000Syntax stxMP Syntax stxMS Midi Settings= MS Midi Set up Function Midi settings = NM Note Map MM MMc set up for AR-3000MT MTc set up for AR-3000Function MTC settings Syntax stxMT Syntax stxNM= BR Baud Rate = DC Display ContrastExample DP0,A1,,A3,A4,,A16 DL Direct pLay for AR-3000 Function Direct Playback settingStxDP Syntax stxDLSM SysteM for AR-2000Function System settings Syntax stxSM AR-3000 RS-232C Reference Syntax stxEQ StxBO3Q pattern phrase reQuest for AR-3000 Request Commands2Q pattern phrase reQuest for AR-2000 GQ sonG phrase reQuest for AR-3000= DQ Direct play reQuest = AQ All reQuest= CQ Card reQuest = NQ Note map reQuest = LQ dispLay contrast reQuest= MQ Memory reQuest Syntax stxNQ * aYQ sYstem reQuest for AR-3000 Syntax stxYQ= VR VeRsion = UQ coUnt play reQuestSyntax stxUQ = Xon 11H/Xoff 13H Reply Commands= ER ERror = CS Card SetCard ID Created automatically Reserved SU phrase Set Up for AR-2000 Function Phrase setting output S**F*S, **H**M**S**F*S,*,*, **H**M**S**F**S, **H**M**S**F**S Endless Syntax stxME Master Slave Sync Source Internal = CR Card Remain = CE Count play sEt upSyntax stxAC Syntax stxCR= DP Direct Play SY SYstem for AR-3000 Function System setting output Syntax stxVR = TI Time stamp InfoSyntax stxTI AR-3000 RS-232C Reference Syntax stxER * a = AE Auto inc rEc startSyntax stxAE S**** a = Xon 11H / Xoff 13H Editing Commands AR-3000 Commands List 1 AR-2000 Compatible Commands List# Control Commands # Playback Commands # Setting Commands # Card Settings# Setting Output Commands # Reply Commands# Commands sent from the AR-3000 to the external device Reply Commands# Midi Settings # Editing Commands # Card Editing# Setting Commands # Phrase Settings # System Settings# Setting Output Commands # Phrase Settings Characters That Can Be Used in Phrase Names and Card NamesSample Algorithms Playing Back a PhraseRecording Nomal Recording Recording Time-Stamped Recording What is the Phrase Output Counter? Deleting a Phrase