Roland RS 232C manual = PL PLay, If Dual Mono Mode is on, = RL Relative time pLay

Page 13

r

= PL (PLay)

Function: Playback start

Syntax: stxPL;

Note: If the playback phrase has not been specified, the minimum default value (normally A001) will be used. The phrases specified by the PA command will be played back consecutively.

* If Dual Mono Mode is ON

Since phrases will be played back from the L or the R output depending on whether they are odd or even numbered phrases, phrases specified by the PA command will automatically be assigned to the playback memory; odd-numbered phrases will be played back from the L output, and even-numbered phrases will be played back from the R output. It is not possible to playback the L and R channels independently.

= RL ( Relative time pLay )

Function: Playback from the Middle of a Phrase

Syntax: stxRL: * , HMSF ; stxRL: * , HM**S ;

	a	b
a Locate Forward / Backward			b Offset Time
0	Backward		0H0M0S0F – 11H59M59S
1	Forward		0H0M0S0F – 11H59M59S**F

Example) stxRL:1,0H10M59S0F;

-After specifying a phrase: Playback begins 10 minutes 59 seconds from the beginning of the phrase of the specified number.

-While playback is paused: Playback begins from the point that is 10 minutes 59 seconds after the point where the pause was initiated.

Note: The number of digits for **F (frame) increases according to the value of MTC type. The range in which the offset time can be specified is valid only within a single phrase. An offset time that exceeds the recording time for the phrase cannot be specified.

(The AR-3000 outputs an ER command.) You can play back a phrase from a point offset by a specified time before or after a paused point by sending this command while playback is paused (see the PE command).

*When “Return Specified” is issued with an offset time longer than elapsed time: The phrase is played back from the beginning.

*When “Forward Specified” is issued with an offset time longer than the remaining time: An ER command is output and playback is not carried out. (The paused state remains in effect, so specify a new offset time and send an RL command again.)

Caution: The command is not compatible with the Dual Mono.

Phrases other than audio phrases cannot be specified.

= ST (STop)

Function: Halting playback/recording

Syntax: stxST;

AR-3000 RS-232C Reference -8

Image 13

Contents AR-3000 RS-232C Reference version RS-232C ReferenceSetup ContentsOverview of Commands Details of each CommandSetting Commands ACK Appendix Connector and Cable If You Have Been Using the AR-2000About the RS-232C Interface HandshakingComputer Settings Setup ProcedureAR-3000 Settings Connections with the ComputerCommand Structure Baud Rate SettingsCommunication Protocol Stx + DM command Precautions Command FormatAbout Input Parameters About Output ParametersDetails of each Command = PAPhrAse Control Commands= PE PausE Phrases other than audio phrases cannot be specified= PL PLay If Dual Mono Mode is on= RL Relative time pLay Syntax stxRL * , **H**M**S**F stxRL * , **H**M**SStxAE Recording CommandsExample stxAE2001,3,1,8,59,0,0,1,0 = RE REc startSyntax stxRM **** , * , * , * , * , * , * a b c d e f g = RM Rec ModeExample RMA1,3,2,1,0,1,1 = DM Delete Mode Editing Commands= CD Card Delete Function Delete Card Syntax stxDM = CP Card coPyLW phrase Lock sWitch for AR-3000 = LS phrase Lock Switch= FM ForMat = PC Phrase Copy Function Copy phrase Syntax stxDM = SP Setting coPy Function System copy Syntax stxDM= PD Phrase Delete = PI Phrase sIlencerStxPM StxPV ****,**H**M**S**F*STS Time Stretch for AR-3000 StxTSSyntax3 Mono1 , Mono2 to Stereo stxDM StxRT StxDM StxRTPattern Phrase Settings Setting CommandsExample stxCV0,ABCDEFGH Syntax stxPU **** , * , **** , **S* , .... , **** , **SSong Phrase number Phrase number to be played back Example SUA001,ABCDEFGHIJK,100,10S5,1,5M0S,1,5M10S,120,0 Phrase SettingsPP phrase Playback Point set up for AR-3000 PO Phrase control Out set up for AR-3000Syntax stxPO **** , *,**M**S Syntax stxPP **** , **H**M**S**F*S, **H**M**S**F*SSyntax stxMP MPphrase Midi temPo set up for AR-3000Syntax stxTT = MS Midi Set up Function Midi settings Midi SettingsSyntax stxMS MT MTc set up for AR-3000Function MTC settings Syntax stxMT MM MMc set up for AR-3000= NM Note Map Syntax stxNM= DC Display Contrast = BR Baud RateStxDP DL Direct pLay for AR-3000 Function Direct Playback settingExample DP0,A1,,A3,A4,,A16 Syntax stxDLSM SysteM for AR-2000Function System settings Syntax stxSM AR-3000 RS-232C Reference StxBO Syntax stxEQ2Q pattern phrase reQuest for AR-2000 Request Commands3Q pattern phrase reQuest for AR-3000 GQ sonG phrase reQuest for AR-3000= CQ Card reQuest = AQ All reQuest= DQ Direct play reQuest = MQ Memory reQuest = LQ dispLay contrast reQuest= NQ Note map reQuest Syntax stxNQ * aSyntax stxYQ YQ sYstem reQuest for AR-3000Syntax stxUQ = UQ coUnt play reQuest= VR VeRsion = ER ERror Reply Commands= Xon 11H/Xoff 13H = CS Card SetCard ID Created automatically Reserved SU phrase Set Up for AR-2000 Function Phrase setting output S**F*S, **H**M**S**F*S,*,*, **H**M**S**F**S, **H**M**S**F**S Endless Syntax stxME Master Slave Sync Source Internal Syntax stxAC = CE Count play sEt up= CR Card Remain Syntax stxCR= DP Direct Play SY SYstem for AR-3000 Function System setting output Syntax stxTI = TI Time stamp InfoSyntax stxVR AR-3000 RS-232C Reference Syntax stxAE S**** a = AE Auto inc rEc startSyntax stxER * a = Xon 11H / Xoff 13H # Control Commands # Playback Commands AR-3000 Commands List 1 AR-2000 Compatible Commands ListEditing Commands # Setting Commands # Card Settings# Commands sent from the AR-3000 to the external device # Reply Commands# Setting Output Commands Reply Commands# Setting Commands # Phrase Settings # Editing Commands # Card Editing# Midi Settings # System SettingsCharacters That Can Be Used in Phrase Names and Card Names # Setting Output Commands # Phrase SettingsPlaying Back a Phrase Sample AlgorithmsRecording Nomal Recording Recording Time-Stamped Recording What is the Phrase Output Counter? Deleting a Phrase