Roland RS 232C manual Editing Commands, = DM Delete Mode, = CP Card coPy

Page 16

r

4.2.2Editing Commands

=DM (Delete Mode)

Function: Enable execution of editing commands.

Syntax: stxDM;

Note: In order for editing commands to be executed, the DM command must be used to put the unit into Delete mode. For the communication protocol, refer to 4.1 2) Editing commands.

Caution:When Delete mode is exited, the AR-3000 will automatically output a CC command. The AR-3000 automatically escapes from the Delete mode two minutes after the DM command is issued. To run editing commands, send a DM command again to enter the Delete mode.

Card Editing

=CD (Card Delete) Function: Delete Card Syntax: stxDM;

stxCD: * ;

a

aCard in slot

0Card in slot A

1Card in slot B

Example) CD:0;

Erase all phrases from a PC card in slot A.

=CP (Card coPy)

Function: Copy Card

Syntax: stxDM;

stxCP;

Note: This copies the contents of the card in slot A to the card in slot B.

>CO ( Card cOnvert for AR-3000 ) Function: Convert Card Syntax: stxDM;

stxCO: * , * ;

a b

aConvert type

0AR-3000 to AR-2000

1AR-2000 to AR-3000

bSelect card

0Card in slot A to Card in slot A

1Card in slot A to Card in slot B

AR-3000 RS-232C Reference -11

Image 16

Contents RS-232C Reference AR-3000 RS-232C Reference versionContents SetupOverview of Commands Details of each CommandSetting Commands ACK Appendix If You Have Been Using the AR-2000 Connector and CableAbout the RS-232C Interface HandshakingSetup Procedure Computer SettingsAR-3000 Settings Connections with the ComputerCommand Structure Baud Rate SettingsCommunication Protocol Stx + DM command Command Format PrecautionsAbout Input Parameters About Output ParametersDetails of each Command Control Commands = PAPhrAse= PE PausE Phrases other than audio phrases cannot be specifiedIf Dual Mono Mode is on = PL PLay= RL Relative time pLay Syntax stxRL * , **H**M**S**F stxRL * , **H**M**SRecording Commands StxAEExample stxAE2001,3,1,8,59,0,0,1,0 = RE REc startSyntax stxRM **** , * , * , * , * , * , * a b c d e f g = RM Rec ModeExample RMA1,3,2,1,0,1,1 Editing Commands = DM Delete Mode= CD Card Delete Function Delete Card Syntax stxDM = CP Card coPyLW phrase Lock sWitch for AR-3000 = LS phrase Lock Switch= FM ForMat = SP Setting coPy Function System copy Syntax stxDM = PC Phrase Copy Function Copy phrase Syntax stxDM= PD Phrase Delete = PI Phrase sIlencerStxPV ****,**H**M**S**F*S StxPMTS Time Stretch for AR-3000 StxTSStxDM StxRT Syntax3 Mono1 , Mono2 to Stereo stxDM StxRTSetting Commands Pattern Phrase SettingsExample stxCV0,ABCDEFGH Syntax stxPU **** , * , **** , **S* , .... , **** , **SSong Phrase number Phrase number to be played back Phrase Settings Example SUA001,ABCDEFGHIJK,100,10S5,1,5M0S,1,5M10S,120,0PO Phrase control Out set up for AR-3000 PP phrase Playback Point set up for AR-3000Syntax stxPO **** , *,**M**S Syntax stxPP **** , **H**M**S**F*S, **H**M**S**F*SSyntax stxMP MPphrase Midi temPo set up for AR-3000Syntax stxTT = MS Midi Set up Function Midi settings Midi SettingsSyntax stxMS MM MMc set up for AR-3000 MT MTc set up for AR-3000Function MTC settings Syntax stxMT= NM Note Map Syntax stxNM= BR Baud Rate = DC Display ContrastDL Direct pLay for AR-3000 Function Direct Playback setting StxDPExample DP0,A1,,A3,A4,,A16 Syntax stxDLSM SysteM for AR-2000Function System settings Syntax stxSM AR-3000 RS-232C Reference Syntax stxEQ StxBORequest Commands 2Q pattern phrase reQuest for AR-20003Q pattern phrase reQuest for AR-3000 GQ sonG phrase reQuest for AR-3000= CQ Card reQuest = AQ All reQuest= DQ Direct play reQuest = LQ dispLay contrast reQuest = MQ Memory reQuest= NQ Note map reQuest Syntax stxNQ * aYQ sYstem reQuest for AR-3000 Syntax stxYQSyntax stxUQ = UQ coUnt play reQuest= VR VeRsion Reply Commands = ER ERror= Xon 11H/Xoff 13H = CS Card SetCard ID Created automatically Reserved SU phrase Set Up for AR-2000 Function Phrase setting output S**F*S, **H**M**S**F*S,*,*, **H**M**S**F**S, **H**M**S**F**S Endless Syntax stxME Master Slave Sync Source Internal = CE Count play sEt up Syntax stxAC= CR Card Remain Syntax stxCR= DP Direct Play SY SYstem for AR-3000 Function System setting output Syntax stxTI = TI Time stamp InfoSyntax stxVR AR-3000 RS-232C Reference Syntax stxAE S**** a = AE Auto inc rEc startSyntax stxER * a = Xon 11H / Xoff 13H AR-3000 Commands List 1 AR-2000 Compatible Commands List # Control Commands # Playback CommandsEditing Commands # Setting Commands # Card Settings# Reply Commands # Commands sent from the AR-3000 to the external device# Setting Output Commands Reply Commands# Editing Commands # Card Editing # Setting Commands # Phrase Settings# Midi Settings # System Settings# Setting Output Commands # Phrase Settings Characters That Can Be Used in Phrase Names and Card NamesSample Algorithms Playing Back a PhraseRecording Nomal Recording Recording Time-Stamped Recording What is the Phrase Output Counter? Deleting a Phrase