Roland RS 232C manual Syntax stxAC, = CE Count play sEt up, = CR Card Remain, Syntax stxCR

Page 45

r

System Settings

= AC (ACtive)

Function: Active sensing reply

Syntax: stxAC: * , **** ;

a b

aStatus of AR-3000

0 During playback

1 During recording

2 During recording pause

3 During playback pause

bPhrase number

Note: During Dual Mono Mode, this is output twice. refer to the 4.2.4 AC command

= CE (Count play sEt up)

Function:	Program (Count) Playback setting output
Syntax:	stxCE: * , * , ** , , .... , ** ;
			a b c	c .... c
	a	Card in slot
		0	Card in slot A
		1	Card in slot B
	b	Program Playback patterns ( 1 - 5 )
	c	Phrase number to be played back (up to 100 phrases)

Note: refer to UQ command

= CR (Card Remain)

Function: Card remaining capacity output

Syntax: stxCR: * , * ;

a b

aRemaining capacity of card A

bRemaining capacity of card B

Note: unit: byte. refer to MQ command

If the card is in AR-2000 format, AR output '0' for remaining capacity.

= DC (Display Contrast)

Function: Display Contrast setting output

Syntax: stxDC: *** ;

a

a Display contrast ( -10 - +10 )

Note: refer to LQ command

AR-3000 RS-232C Reference -40

Image 45

Contents AR-3000 RS-232C Reference version RS-232C ReferenceSetup ContentsOverview of Commands Details of each CommandSetting Commands ACK Appendix Connector and Cable If You Have Been Using the AR-2000About the RS-232C Interface HandshakingComputer Settings Setup ProcedureAR-3000 Settings Connections with the ComputerBaud Rate Settings Command StructureCommunication Protocol Stx + DM command Precautions Command FormatAbout Input Parameters About Output ParametersDetails of each Command = PAPhrAse Control Commands= PE PausE Phrases other than audio phrases cannot be specified= PL PLay If Dual Mono Mode is on= RL Relative time pLay Syntax stxRL * , **H**M**S**F stxRL * , **H**M**SStxAE Recording CommandsExample stxAE2001,3,1,8,59,0,0,1,0 = RE REc start= RM Rec Mode Syntax stxRM **** , * , * , * , * , * , * a b c d e f gExample RMA1,3,2,1,0,1,1 = DM Delete Mode Editing Commands= CD Card Delete Function Delete Card Syntax stxDM = CP Card coPy= LS phrase Lock Switch LW phrase Lock sWitch for AR-3000= FM ForMat = PC Phrase Copy Function Copy phrase Syntax stxDM = SP Setting coPy Function System copy Syntax stxDM= PD Phrase Delete = PI Phrase sIlencerStxPM StxPV ****,**H**M**S**F*STS Time Stretch for AR-3000 StxTSSyntax3 Mono1 , Mono2 to Stereo stxDM StxRT StxDM StxRTPattern Phrase Settings Setting CommandsExample stxCV0,ABCDEFGH Syntax stxPU **** , * , **** , **S* , .... , **** , **SSong Phrase number Phrase number to be played back Example SUA001,ABCDEFGHIJK,100,10S5,1,5M0S,1,5M10S,120,0 Phrase SettingsPP phrase Playback Point set up for AR-3000 PO Phrase control Out set up for AR-3000Syntax stxPO **** , *,**M**S Syntax stxPP **** , **H**M**S**F*S, **H**M**S**F*SMPphrase Midi temPo set up for AR-3000 Syntax stxMPSyntax stxTT Midi Settings = MS Midi Set up Function Midi settingsSyntax stxMS MT MTc set up for AR-3000Function MTC settings Syntax stxMT MM MMc set up for AR-3000= NM Note Map Syntax stxNM= DC Display Contrast = BR Baud RateStxDP DL Direct pLay for AR-3000 Function Direct Playback settingExample DP0,A1,,A3,A4,,A16 Syntax stxDLSM SysteM for AR-2000Function System settings Syntax stxSM AR-3000 RS-232C Reference StxBO Syntax stxEQ2Q pattern phrase reQuest for AR-2000 Request Commands3Q pattern phrase reQuest for AR-3000 GQ sonG phrase reQuest for AR-3000= AQ All reQuest = CQ Card reQuest= DQ Direct play reQuest = MQ Memory reQuest = LQ dispLay contrast reQuest= NQ Note map reQuest Syntax stxNQ * aSyntax stxYQ YQ sYstem reQuest for AR-3000= UQ coUnt play reQuest Syntax stxUQ= VR VeRsion = ER ERror Reply Commands= Xon 11H/Xoff 13H = CS Card SetCard ID Created automatically Reserved SU phrase Set Up for AR-2000 Function Phrase setting output S**F*S, **H**M**S**F*S,*,*, **H**M**S**F**S, **H**M**S**F**S Endless Syntax stxME Master Slave Sync Source Internal Syntax stxAC = CE Count play sEt up= CR Card Remain Syntax stxCR= DP Direct Play SY SYstem for AR-3000 Function System setting output = TI Time stamp Info Syntax stxTISyntax stxVR AR-3000 RS-232C Reference = AE Auto inc rEc start Syntax stxAE S**** aSyntax stxER * a = Xon 11H / Xoff 13H # Control Commands # Playback Commands AR-3000 Commands List 1 AR-2000 Compatible Commands ListEditing Commands # Setting Commands # Card Settings# Commands sent from the AR-3000 to the external device # Reply Commands# Setting Output Commands Reply Commands# Setting Commands # Phrase Settings # Editing Commands # Card Editing# Midi Settings # System SettingsCharacters That Can Be Used in Phrase Names and Card Names # Setting Output Commands # Phrase SettingsPlaying Back a Phrase Sample AlgorithmsRecording Nomal Recording Recording Time-Stamped Recording What is the Phrase Output Counter? Deleting a Phrase