Roland RS 232C manual YQ sYstem reQuest for AR-3000, Syntax stxYQ

Page 36

a

a Card in slot

0 Card in slot A

1 Card in slot B refer to SM command

stxSQ: * ;

Function:

Syntax:

System setting contents request

* About the Phrase Output Counter

The AR-3000 contains the Phrase Output Counter. The maximum value of this counter is the maximum phrase number of each card. The counter is reset (i.e., to the lowest phrase number) by the AQ command. So you can request each phrase settings of all phrases in the card by sequentially using the QQ command’s function 2 after resetting the counter.

< SQ (System reQuest for AR-2000)

The incremented value will skip phrase numbers which are not recorded yet, and will Be up to the next recorded phrase number. If the PQ command is used to request output even after the setting information of the last phrase has been output, the AR-3000 will output “stx ER:101;”.

In the case of a Pattern Phrase, you must use the separately described 3Q command to request output of the settings. (* refer to 3Q command)

Note:

stxQQ:;

Syntax:

If the phrase number is not specified as a parameter, the AR-3000 will output the phrase settings for automatically incremented phrase number by the Phrase Output Counter.

Function2:

The phrase settings for the specified phrase number will be output.

The value of the Phrase Output Counter (described below) will not change. (* refer to the RU command)

Note:

> QQ (phrase reQuest for AR-3000)Function1: Phrase setting contents request Syntax: stxQQ: **** ;

a

a Phrase number

r

Note:

> YQ (sYstem reQuest for AR-3000)

Function: System setting contents request

Syntax: stxYQ: * ;

a

aCard in slot

0 Card in slot A

1 Card in slot B

Note: refer to SY command

AR-3000 RS-232C Reference -31

Image 36

Contents RS-232C Reference AR-3000 RS-232C Reference versionContents SetupOverview of Commands Details of each CommandSetting Commands ACK Appendix If You Have Been Using the AR-2000 Connector and CableAbout the RS-232C Interface HandshakingSetup Procedure Computer SettingsAR-3000 Settings Connections with the ComputerBaud Rate Settings Command StructureCommunication Protocol Stx + DM command Command Format PrecautionsAbout Input Parameters About Output ParametersDetails of each Command Control Commands = PAPhrAse= PE PausE Phrases other than audio phrases cannot be specifiedIf Dual Mono Mode is on = PL PLay= RL Relative time pLay Syntax stxRL * , **H**M**S**F stxRL * , **H**M**SRecording Commands StxAEExample stxAE2001,3,1,8,59,0,0,1,0 = RE REc start= RM Rec Mode Syntax stxRM **** , * , * , * , * , * , * a b c d e f gExample RMA1,3,2,1,0,1,1 Editing Commands = DM Delete Mode= CD Card Delete Function Delete Card Syntax stxDM = CP Card coPy= LS phrase Lock Switch LW phrase Lock sWitch for AR-3000= FM ForMat = SP Setting coPy Function System copy Syntax stxDM = PC Phrase Copy Function Copy phrase Syntax stxDM= PD Phrase Delete = PI Phrase sIlencerStxPV ****,**H**M**S**F*S StxPMTS Time Stretch for AR-3000 StxTSStxDM StxRT Syntax3 Mono1 , Mono2 to Stereo stxDM StxRTSetting Commands Pattern Phrase SettingsExample stxCV0,ABCDEFGH Syntax stxPU **** , * , **** , **S* , .... , **** , **SSong Phrase number Phrase number to be played back Phrase Settings Example SUA001,ABCDEFGHIJK,100,10S5,1,5M0S,1,5M10S,120,0PO Phrase control Out set up for AR-3000 PP phrase Playback Point set up for AR-3000Syntax stxPO **** , *,**M**S Syntax stxPP **** , **H**M**S**F*S, **H**M**S**F*SMPphrase Midi temPo set up for AR-3000 Syntax stxMPSyntax stxTT Midi Settings = MS Midi Set up Function Midi settingsSyntax stxMS MM MMc set up for AR-3000 MT MTc set up for AR-3000Function MTC settings Syntax stxMT= NM Note Map Syntax stxNM= BR Baud Rate = DC Display ContrastDL Direct pLay for AR-3000 Function Direct Playback setting StxDPExample DP0,A1,,A3,A4,,A16 Syntax stxDLSM SysteM for AR-2000Function System settings Syntax stxSM AR-3000 RS-232C Reference Syntax stxEQ StxBO Request Commands 2Q pattern phrase reQuest for AR-2000 3Q pattern phrase reQuest for AR-3000 GQ sonG phrase reQuest for AR-3000= AQ All reQuest = CQ Card reQuest= DQ Direct play reQuest = LQ dispLay contrast reQuest = MQ Memory reQuest= NQ Note map reQuest Syntax stxNQ * aYQ sYstem reQuest for AR-3000 Syntax stxYQ= UQ coUnt play reQuest Syntax stxUQ= VR VeRsion Reply Commands = ER ERror= Xon 11H/Xoff 13H = CS Card SetCard ID Created automatically Reserved SU phrase Set Up for AR-2000 Function Phrase setting output S**F*S, **H**M**S**F*S,*,*, **H**M**S**F**S, **H**M**S**F**S Endless Syntax stxME Master Slave Sync Source Internal = CE Count play sEt up Syntax stxAC= CR Card Remain Syntax stxCR= DP Direct Play SY SYstem for AR-3000 Function System setting output = TI Time stamp Info Syntax stxTISyntax stxVR AR-3000 RS-232C Reference = AE Auto inc rEc start Syntax stxAE S**** aSyntax stxER * a = Xon 11H / Xoff 13H AR-3000 Commands List 1 AR-2000 Compatible Commands List # Control Commands # Playback CommandsEditing Commands # Setting Commands # Card Settings# Reply Commands # Commands sent from the AR-3000 to the external device# Setting Output Commands Reply Commands# Editing Commands # Card Editing # Setting Commands # Phrase Settings# Midi Settings # System Settings# Setting Output Commands # Phrase Settings Characters That Can Be Used in Phrase Names and Card NamesSample Algorithms Playing Back a PhraseRecording Nomal Recording Recording Time-Stamped Recording What is the Phrase Output Counter? Deleting a Phrase