Roland RS 232C manual Characters That Can Be Used in Phrase Names and Card Names

Page 55

r

#Commands sent from the AR-3000 to the external device

#Setting Output Commands

#Phrase Settings

PS Pattern phrase Set up

SSSong phrase Set up

RU phRase set Up

#MIDI Settings

ME Midi sEt up

# System Settings

Pattern phrase setting output	type2
Song phrase setting output	type2
Phrase setting output	type2
MIDI setting output	type2

SY

SYstem

System setting output

type2

Caution1:

STX(02H) is attached to top of the command, and some commands has parameters with it. In this commands list, STX(02H) and parameter are omitted.

Caution2:

Type0: Those consisting only of a control code.

Type1: Commands with no parameters.

Type2: Commands with parameters

5.2Characters That Can Be Used in Phrase Names and Card Names

Blank locations in this table cannot be used. However, 20H is used as a space character.

		Lower 4 Bit

		0 1 2 3 4 5 6 7 8 9 a b c d e f

	0

	1

	2	! #$%& ( )	-
		! #$%& ( )	-

H	3	0 1 2 3 4 5 6 7 8 9

i	4	@AB CDE FGH I J KLMNO

g	5	PQR S TUVWXY Z [	] ^ _

h	6

e	7

r	8

	9
4	a

B	b
i	c

t	d
	e

	f

AR-3000 RS-232C Reference -50

Image 55

Contents AR-3000 RS-232C Reference version RS-232C ReferenceDetails of each Command ContentsSetup Overview of CommandsSetting Commands ACK Appendix Handshaking If You Have Been Using the AR-2000Connector and Cable About the RS-232C InterfaceConnections with the Computer Setup ProcedureComputer Settings AR-3000 SettingsCommand Structure Baud Rate SettingsCommunication Protocol Stx + DM command About Output Parameters Command FormatPrecautions About Input ParametersDetails of each Command Phrases other than audio phrases cannot be specified Control Commands= PAPhrAse = PE PausESyntax stxRL * , **H**M**S**F stxRL * , **H**M**S If Dual Mono Mode is on= PL PLay = RL Relative time pLay= RE REc start Recording CommandsStxAE Example stxAE2001,3,1,8,59,0,0,1,0Syntax stxRM **** , * , * , * , * , * , * a b c d e f g = RM Rec ModeExample RMA1,3,2,1,0,1,1 = CP Card coPy Editing Commands= DM Delete Mode = CD Card Delete Function Delete Card Syntax stxDMLW phrase Lock sWitch for AR-3000 = LS phrase Lock Switch= FM ForMat = PI Phrase sIlencer = SP Setting coPy Function System copy Syntax stxDM= PC Phrase Copy Function Copy phrase Syntax stxDM = PD Phrase DeleteStxTS StxPV ****,**H**M**S**F*SStxPM TS Time Stretch for AR-3000Syntax3 Mono1 , Mono2 to Stereo stxDM StxRT StxDM StxRTSyntax stxPU **** , * , **** , **S* , .... , **** , **S Setting CommandsPattern Phrase Settings Example stxCV0,ABCDEFGHSong Phrase number Phrase number to be played back Example SUA001,ABCDEFGHIJK,100,10S5,1,5M0S,1,5M10S,120,0 Phrase SettingsSyntax stxPP **** , **H**M**S**F*S, **H**M**S**F*S PO Phrase control Out set up for AR-3000PP phrase Playback Point set up for AR-3000 Syntax stxPO **** , *,**M**SSyntax stxMP MPphrase Midi temPo set up for AR-3000Syntax stxTT = MS Midi Set up Function Midi settings Midi SettingsSyntax stxMS Syntax stxNM MM MMc set up for AR-3000MT MTc set up for AR-3000Function MTC settings Syntax stxMT = NM Note Map= DC Display Contrast = BR Baud RateSyntax stxDL DL Direct pLay for AR-3000 Function Direct Playback settingStxDP Example DP0,A1,,A3,A4,,A16SM SysteM for AR-2000Function System settings Syntax stxSM AR-3000 RS-232C Reference StxBO Syntax stxEQGQ sonG phrase reQuest for AR-3000 Request Commands2Q pattern phrase reQuest for AR-2000 3Q pattern phrase reQuest for AR-3000= CQ Card reQuest = AQ All reQuest= DQ Direct play reQuest Syntax stxNQ * a = LQ dispLay contrast reQuest= MQ Memory reQuest = NQ Note map reQuestSyntax stxYQ YQ sYstem reQuest for AR-3000Syntax stxUQ = UQ coUnt play reQuest= VR VeRsion = CS Card Set Reply Commands= ER ERror = Xon 11H/Xoff 13HCard ID Created automatically Reserved SU phrase Set Up for AR-2000 Function Phrase setting output S**F*S, **H**M**S**F*S,*,*, **H**M**S**F**S, **H**M**S**F**S Endless Syntax stxME Master Slave Sync Source Internal Syntax stxCR = CE Count play sEt upSyntax stxAC = CR Card Remain= DP Direct Play SY SYstem for AR-3000 Function System setting output Syntax stxTI = TI Time stamp InfoSyntax stxVR AR-3000 RS-232C Reference Syntax stxAE S**** a = AE Auto inc rEc startSyntax stxER * a = Xon 11H / Xoff 13H # Setting Commands # Card Settings AR-3000 Commands List 1 AR-2000 Compatible Commands List# Control Commands # Playback Commands Editing CommandsReply Commands # Reply Commands# Commands sent from the AR-3000 to the external device # Setting Output Commands# System Settings # Editing Commands # Card Editing# Setting Commands # Phrase Settings # Midi SettingsCharacters That Can Be Used in Phrase Names and Card Names # Setting Output Commands # Phrase SettingsPlaying Back a Phrase Sample AlgorithmsRecording Nomal Recording Recording Time-Stamped Recording What is the Phrase Output Counter? Deleting a Phrase