Roland RS 232C manual Reply Commands, = ER ERror, = Xon 11H/Xoff 13H, = CS Card Set

Page 38

r

4.2.5Reply Commands

= ACK

Function: Response to normal reception of a command

Syntax: ACK (06H)

= ER (ERror)

Function: Reply to the AR-3000 when an error has occurred

Syntax: stxER: * ;

a

aError number

0Send this command to the AR-3000 when the output of the AR-3000 could not be read (In the case of a request command, the AR-3000 will re-transmit the Setting output command.)

1Send this command when the output of the AR-3000 for confirmation is incorrect in Delete mode. Then the command you transmitted will be canceled, and the AR-3000 will automatically exit Delete mode.

=Xon (11H)/Xoff (13H)

Function: Allow or disable transmission. Used for handshaking.

Syntax: Xon is 11H only (transmission permitted)

Xoff is 13H only (transmission disabled)

4.3Commands Sent from the AR-3000 to the External Device (Computer)

The following two types of commands are sent from the AR-3000 to an external device. In this explanation, “external device” refers to the computer. “AR” refers to the AR-3000.

1) Setting output commands

These commands output the current setting status of the AR-3000. They are output in response to a request command from the external device.

2) Reply commands

Reply commands are necessary for communication control, such as acknowledgment that a command was correctly received, etc.

4.4Details of Commands Sent from the AR-3000 to the External Device (Computer)

4.4.1Setting Output Commands

=CS (Card Set)

Function: Card setting output

Syntax: stxCS: * ,“********”, * , * , * , *** , * ;

a

b

c d e

f

g

aCard in slot

0Card in slot A

1Card in slot B

bCard name (8 characters)

cReserved

dReserved

eMaximum number of phrase

0(250)

1(500)

1 (1000)

AR-3000 RS-232C Reference -33

Image 38

Contents RS-232C Reference AR-3000 RS-232C Reference versionOverview of Commands ContentsSetup Details of each CommandSetting Commands ACK Appendix About the RS-232C Interface If You Have Been Using the AR-2000Connector and Cable HandshakingAR-3000 Settings Setup ProcedureComputer Settings Connections with the ComputerCommunication Protocol Baud Rate SettingsCommand Structure Stx + DM command About Input Parameters Command FormatPrecautions About Output ParametersDetails of each Command = PE PausE Control Commands= PAPhrAse Phrases other than audio phrases cannot be specified= RL Relative time pLay If Dual Mono Mode is on= PL PLay Syntax stxRL * , **H**M**S**F stxRL * , **H**M**SExample stxAE2001,3,1,8,59,0,0,1,0 Recording CommandsStxAE = RE REc startExample RMA1,3,2,1,0,1,1 = RM Rec ModeSyntax stxRM **** , * , * , * , * , * , * a b c d e f g = CD Card Delete Function Delete Card Syntax stxDM Editing Commands= DM Delete Mode = CP Card coPy= FM ForMat = LS phrase Lock SwitchLW phrase Lock sWitch for AR-3000 = PD Phrase Delete = SP Setting coPy Function System copy Syntax stxDM= PC Phrase Copy Function Copy phrase Syntax stxDM = PI Phrase sIlencerTS Time Stretch for AR-3000 StxPV ****,**H**M**S**F*SStxPM StxTSStxDM StxRT Syntax3 Mono1 , Mono2 to Stereo stxDM StxRTExample stxCV0,ABCDEFGH Setting CommandsPattern Phrase Settings Syntax stxPU **** , * , **** , **S* , .... , **** , **SSong Phrase number Phrase number to be played back Phrase Settings Example SUA001,ABCDEFGHIJK,100,10S5,1,5M0S,1,5M10S,120,0Syntax stxPO **** , *,**M**S PO Phrase control Out set up for AR-3000PP phrase Playback Point set up for AR-3000 Syntax stxPP **** , **H**M**S**F*S, **H**M**S**F*SSyntax stxTT MPphrase Midi temPo set up for AR-3000Syntax stxMP Syntax stxMS Midi Settings= MS Midi Set up Function Midi settings = NM Note Map MM MMc set up for AR-3000MT MTc set up for AR-3000Function MTC settings Syntax stxMT Syntax stxNM= BR Baud Rate = DC Display ContrastExample DP0,A1,,A3,A4,,A16 DL Direct pLay for AR-3000 Function Direct Playback settingStxDP Syntax stxDLSM SysteM for AR-2000Function System settings Syntax stxSM AR-3000 RS-232C Reference Syntax stxEQ StxBO3Q pattern phrase reQuest for AR-3000 Request Commands2Q pattern phrase reQuest for AR-2000 GQ sonG phrase reQuest for AR-3000= DQ Direct play reQuest = AQ All reQuest= CQ Card reQuest = NQ Note map reQuest = LQ dispLay contrast reQuest= MQ Memory reQuest Syntax stxNQ * aYQ sYstem reQuest for AR-3000 Syntax stxYQ= VR VeRsion = UQ coUnt play reQuestSyntax stxUQ = Xon 11H/Xoff 13H Reply Commands= ER ERror = CS Card SetCard ID Created automatically Reserved SU phrase Set Up for AR-2000 Function Phrase setting output S**F*S, **H**M**S**F*S,*,*, **H**M**S**F**S, **H**M**S**F**S Endless Syntax stxME Master Slave Sync Source Internal = CR Card Remain = CE Count play sEt upSyntax stxAC Syntax stxCR= DP Direct Play SY SYstem for AR-3000 Function System setting output Syntax stxVR = TI Time stamp InfoSyntax stxTI AR-3000 RS-232C Reference Syntax stxER * a = AE Auto inc rEc startSyntax stxAE S**** a = Xon 11H / Xoff 13H Editing Commands AR-3000 Commands List 1 AR-2000 Compatible Commands List# Control Commands # Playback Commands # Setting Commands # Card Settings# Setting Output Commands # Reply Commands# Commands sent from the AR-3000 to the external device Reply Commands# Midi Settings # Editing Commands # Card Editing# Setting Commands # Phrase Settings # System Settings# Setting Output Commands # Phrase Settings Characters That Can Be Used in Phrase Names and Card NamesSample Algorithms Playing Back a PhraseRecording Nomal Recording Recording Time-Stamped Recording What is the Phrase Output Counter? Deleting a Phrase