Manual Timer Programing, Vhs Dvd | JVC DR-MV5S specification

32 EN TIMER RECORDING

Manual Timer Programing

1 Press DVD or VHS to select the deck on which you want to

perform timer programing.

2 For DVD deck

Load a recordable disc.

For VHS deck

You can program each deck to timer-record as many as

Load a cassette with safety tab intact.

8 programs up to 30 days ahead.

3 Press PROG to access the

VHS PRGM CHECK DVD PRGM CHECK

If you do not know the VCR Plus+ number for the program you

Program Check screen.

DATE

START

STOP

DAILY/WEEKLY

REC MODE

wish to record, use the following procedure to set your unit to

● When “PROGRAM FULL

10/07 THU 10:00PM - 10:30PM

05/07 SAT

7:00PM - 8:00PM

WEEKLY

timer-record the program.

DELETE UNWANTED TIMER

11/07 FRI

08:00AM - 09:00AM

11/07 FRI

08:30AM - 09:30AM

PROGRAM” appears on the TV

++++++++++++++++DVD NEW TIMER

PROGRAM ++++++++++++++++

● Make sure that the unit’s built-in clock is set properly.

screen, you need to cancel some

● Turn on the unit.

of the reserved programs.

DISC TIMER PRGM

● Turn on the TV and select the AV mode.

( pg. 35)

EXIT

SELECT WITH [CURSORS]

PROG

SELECT

THEN PRESS [ENTER]

● Slide the TV/DVD switch to DVD.

4 For DVD deck

Press rt w e to select “DVD PRGM CHECK” and press rt to select “DVD NEW TIMER PROGRAM”, then press ENTER.

VHS

DVD

For VHS deck

Press rt w e to select “VHS PRGM CHECK” and press rt to select “VHS NEW TIMER PROGRAM”, then press ENTER.

5 Press rt to set the desired date.

●The current date appears on the TV screen. The date you enter appears in its place.

TIMER PROGRAM

DATE	START	STOP	CH
10/07/03 THU	- - : - -	- - : - -	- -
DAILY/WEEKLY	REC MODE		NAME
	SP		NAME
	SP
EXIT	CONFIRM	SET TIMER PROGRAMING WITH [CURSORS]
PROG	SELECT	THEN PRESS [ENTER]

PROG ENTER

TIMER

6 Press w e to select “START”, then press rt to set the desired start time.

● Each press of rt advances/goes back the start time in 1-min.

increments.

rtwe

● To advance/go back the start time in 30-min. increments, press and

hold rt.

7 Press w e to select “STOP”, then press rt to set the desired stop time.

Cable Box and DBS Receiver Users (DVD Deck Only) To timer-record a satellite broadcast using Manual Timer Programing:

APerform “Manual Timer Programing”.

BSet the cable box or DBS receiver to the appropriate channel before the selected program begins.

C Select “L-1” in step 8.

D Leave the cable box or DBS receiver’s power on.

NOTES:

●When two successive programs are recorded on a DVD-RW disc with Manual Timer Programing function, the beginning of the second one may be left off the recording.

●If the copy limited program is received during timer-recording, the unit enters Record Pause mode. Recording starts again if it is switched to a recordable broadcast during the time you programed.

●In case of a power failure after programing, the unit’s memory backup keeps your selections for approximately 5 seconds.

●Programs that start after midnight must have the next day’s date.

●To record the programs received by cable box or DBS receiver, record on the DVD discs. For details, refer to “Cable Box and DBS Receiver Users (DVD Deck Only)” above.

●Each press of rt advances/goes back the stop time in 1-min. increments.

●To advance/go back the stop time in 30-min. increments, press and hold rt.

8 Press w e to select “CH”, then press rt to select the desired channel.

9 Press w e to select the desired recording option as required.

●Refer to step 6 in “VCR Plus+® Timer Programing” ( pg. 31).

10 Press ENTER to access the Program Confirmation screen.

11 Press ENTER to complete timer programing.

●To program another timer, repeat steps 3 – 11.

●If “PROGRAM OVERLAPPED” appears on the TV screen, see page 35.

12 Press TIMER # to engage the unit’s timer mode. The DVD timer lamp lights up on the unit and the unit is automatically turned off.

●To disengage the timer mode, press TIMER # again.